SS23H20G3SW -silde switch 2P3T
Series:SS23H20G3SW
Type: SS23H20G3SW
RATING:DC 50V 0.3A
FUNCTION:2P3T
- Applications
- Technical parameters
- Remarks
-
1.Digital Products: digital camera, digital video and so on;
2.Remote Control: the remote control of automobile domestic security products;
3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ，refrigerator，washer;air-conditioning and so on;
5.Security Products: visual interphone, monitor and so on;
6.Toys: electric toys and so on;
7.Computer Products: PC camera and so on;
8.Exercises Machines: treadmills, massage armchair and so on;
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
10.Others: laser pen ，Pointer，Wireless mouse remote control pen，Laser projection pen，page turner，electronic pen；MousePen；overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders，automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.
1.DETAIL SPECIFICATIONS:
1.1 OPERATING CHARACTERISTICS
NO.
Items
Test conditions
Criteria
1.1.1
Actuating Force
Measurement shall be made at the nearest
Point of the component or at the point 3mm
From the tip of the actuator(KNOB)
250gf±100gf
1.1.2
Terminal Strength
A static load of (300gf) shall be applied characteristics shall to the terminal for 15 sec in any direction
Mechanical and electrical characteristics shall be satisfied without looseness of actuator
1.1.3
Displacement of actuator (KNOB)
A static load of 10N(1Kgf) shall be applied to the top the actuator(KNOB) and then
Displacement shall be measured to the direction of the arrow.
The lever shall have no serious deformation and function is normally.
1.2 GENERAL CHARACTERISTICS
1.2.1 Application: This specification is applied to SS23H Slide Switch used for electronic equipment.
1.2.2 Operating temperature range:0℃ to 85℃
1.2.3 Test conditions: Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature: 15~35℃
Relative humidity: 45~85%
Air pressure: 86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions Refer to individual product drawing.
1.4. Electrical specifications
NO.
ITEM
TEST CONDITIONS
PERFORMANCE
1.4.1
Contact resistance
Measured at 1KHz small current (100mA or less)
30mΩ MAX
1.4.2
Insulation resistance
Apply a voltage of 500V DC for 1 MIN.
To following portions after which measurement shall be made.
(1)Between body and terminal.
(2) Between terminals.
100MΩ MIN
1.4.3
Dielectric strength
AC 500V rms(50-60Hz) for 1 min trip
Current:0.5mA
(1) Between terminals.
(2) Between individual terminal and frame.
Without damage to parts arcing or breakdown etc
1.5. Environment ResistanceNO.
ITEM
TEST CONDITIONS
PERFORMANCE
1.5.1
Humid test
It was placed in a temperature of 40 + 2 ℃ and a relative humidity of 90~95%. After 96 hours, it was placed at normal room temperature for 1 hours.
No abnormal appearance，Meet the mechanical and electrical properties。
1.5.2
Test standard state
In the absence of a specified case Test the temperature, humidity, and air pressure as follows：
（1） temperature： 5~35°C 。
（2） humidity： 45~85% 。
（3） pressure： 86Kpa~106Kpa 。
1.5.3
Use of temperature range
It is used at -16 C ~ +60 ℃ temperature.
1.5. ENDURANCE
NO.
ITEM
TEST CONDITIONS
PERFORMANCE
1.5.1
Life Test
Without load :
An actuator shall be subject to 10,000 cycles at a speed of 15 to 18 cycles for 1 min.
（1） Contact resistance 100 mΩ MAX.
（2）Insulation resistance 50MΩ MIN.
（3）Withstand voltage AC 500V, 1 minute
（4）Operating force ±30% Initial value
（5）Without damage to parts arcing or breakdown etc.
1.5.2
Solder ability test
The top of the terminals shall be dipped 2mm in the solder bath of 230±5℃ for 3±0.5 seconds.
The area of soldering should be over 75%
1.5.3
Resistance to soldering Heat test
(1) temperature and immersing time
temperature（°C ）
time（S）
dip soldering
260±5
3±1
Manual soldering
360±10
3±1
(2) immersion depth:
immersion depth up to the surface of the board thickness of printed wiring board 1.6mm.
Without deformation of case or excessive looseness of terminals
Mechanical and electrical characteristics shall be satisfied
1.5.4
Heat resistance test
It was placed at a temperature of 70 + 2℃, and then placed at normal room temperature after 48 hours. Then it shall be subjected to the controlled recovery conditions for 1 hour after which measurement shall be made.
1.5.5
Cold tolerance test
It was placed at a temperature of -25±3℃, and then placed at normal room temperature after 48 hours. Then it shall be subjected to the controlled recovery conditions for 1 hour after which measurement shall be made.
2. DRAWING & DIMENSION:
3. CIRCUIT & DIAGRAM:
1. PARTS LIST:
ITEM
PARTS
MATERIALS
QUANTITY
FINISH
1
KNOB
NYLON+94V0
1
BLACK
2
FRAME
STEEL STRIP
1
Ni PLATED
3
BASE
PHENOLIC RESIN
1
BLACK
4
TERMINAL
COPPER STRIP
8
Ag PLATED
5
CONTACT
COPPER STRIP
2
Ag PLATED
6
SPRING PLATE
PBS STRIP
3
NATURAL
2. PACKING:
2.1
Packing material:
Plastic box
2.2
Packing number:
1000 pieces per box 2 inner cartons per shipping carton Each shipping carton 2000 pieces
2.3
Weight:
Gross Weight : 24kg
Net Weight : 21kg
2.4
Size:
550 x 380 x 260 CM
Skype
QQ