SS23H20G3-XD -silde switch 2P3T
RATING:DC 50V 0.3A
- Technical parameters
1.Digital Products: digital camera, digital video and so on;
2.Remote Control: the remote control of automobile domestic security products;
3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ，refrigerator，washer;air-conditioning and so on;
5.Security Products: visual interphone, monitor and so on;
6.Toys: electric toys and so on;
7.Computer Products: PC camera and so on;
8.Exercises Machines: treadmills, massage armchair and so on;
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
10.Others: laser pen ，Pointer，Wireless mouse remote control pen，Laser projection pen，page turner，electronic pen；MousePen；overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders，automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.
1.1 OPERATING CHARACTERISTICS
Measurement shall be made at the nearest
Point of the component or at the point 3mm
From the tip of the actuator(KNOB)
A static load of (300gf) shall be applied characteristics shall to the terminal for 15 sec in any direction
Mechanical and electrical characteristics shall be satisfied without looseness of actuator
Displacement of actuator (KNOB)
A static load of 10N(1Kgf) shall be applied to the top the actuator(KNOB) and then
Displacement shall be measured to the direction of the arrow.
The lever shall have no serious deformation and function is normally.
1.2 GENERAL CHARACTERISTICS
1.2.1 Application: This specification is applied to SS23H Slide Switch used for electronic equipment.
1.2.2 Operating temperature range:0℃ to 85℃
1.2.3 Test conditions: Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature: 15~35℃
Relative humidity: 45~85%
Air pressure: 86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions Refer to individual product drawing.
1.4. Electrical specifications
Measured at 1KHz small current (100mA or less)
Apply a voltage of 500V DC for 1 MIN.
To following portions after which measurement shall be made.
(1)Between body and terminal.
(2) Between terminals.
AC 500V rms(50-60Hz) for 1 min trip
(1) Between terminals.
(2) Between individual terminal and frame.
Without damage to parts arcing or breakdown etc
1.5. Environment Resistance
It was placed in a temperature of 40 + 2 ℃ and a relative humidity of 90~95%. After 96 hours, it was placed at normal room temperature for 1 hours.
No abnormal appearance，Meet the mechanical and electrical properties。
Test standard state
In the absence of a specified case Test the temperature, humidity, and air pressure as follows：
（1） temperature： 5~35°C 。
（2） humidity： 45~85% 。
（3） pressure： 86Kpa~106Kpa 。
Use of temperature range
It is used at -16 C ~ +60 ℃ temperature.
Without load :
An actuator shall be subject to 10,000 cycles at a speed of 15 to 18 cycles for 1 min.
（1） Contact resistance 100 mΩ MAX.
（2）Insulation resistance 50MΩ MIN.
（3）Withstand voltage AC 500V, 1 minute
（4）Operating force ±30% Initial value
（5）Without damage to parts arcing or breakdown etc.
Solder ability test
The top of the terminals shall be dipped 2mm in the solder bath of 230±5℃ for 3±0.5 seconds.
The area of soldering should be over 75%
Resistance to soldering Heat test
(1) temperature and immersing time
(2) immersion depth:
immersion depth up to the surface of the board thickness of printed wiring board 1.6mm.
Without deformation of case or excessive looseness of terminals
Mechanical and electrical characteristics shall be satisfied
Heat resistance test
It was placed at a temperature of 70 + 2℃, and then placed at normal room temperature after 48 hours. Then it shall be subjected to the controlled recovery conditions for 1 hour after which measurement shall be made.
Cold tolerance test
It was placed at a temperature of -25±3℃, and then placed at normal room temperature after 48 hours. Then it shall be subjected to the controlled recovery conditions for 1 hour after which measurement shall be made.
2. DRAWING & DIMENSION:
3. CIRCUIT & DIAGRAM:
1. PARTS LIST:
1000 pieces per box 2 inner cartons per shipping carton Each shipping carton 2000 pieces
Gross Weight : 24kg
Net Weight : 21kg
550 x 380 x 260 CM