
SS12F46G6SW -silde switch 1P2T
Series:SS12F46G6SW
Type: SS12F46G6SW
RATING:DC 50V 0.3A
FUNCTION:1P2T
- Applications
- Technical parameters
- Remarks
-
1.Digital Products: digital camera, digital video and so on;
2.Remote Control: the remote control of automobile domestic security products;
3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ,refrigerator,washer;air-conditioning and so on;
5.Security Products: visual interphone, monitor and so on;
6.Toys: electric toys and so on;
7.Computer Products: PC camera and so on;
8.Exercises Machines: treadmills, massage armchair and so on;
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
10.Others: laser pen ,Pointer,Wireless mouse remote control pen,Laser projection pen,page turner,electronic pen;MousePen;overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders,automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.
1.DETAIL SPECIFICATIONS:
1.1 OPERATING CHARACTERISTICS
NO.
Items
Test conditions
Criteria
1.1.1
Actuating Force
Measurement shall be made at the nearest
Point of the component or at the point 3mm
From the tip of the actuator(KNOB)
250gf±100gf
1.1.2
Terminal Strength
A static load of (500gf) shall be applied characteristics shall to the terminal for 15 sec in any direction
Mechanical and electrical characteristics shall be satisfied without looseness of actuator
1.1.3
Displacement of actuator (KNOB)
A static load of 10N(1Kgf) shall be applied to the top the actuator(KNOB) and then
Displacement shall be measured to the direction of the arrow.
The lever shall have no serious deformation and function is normally.
1.2 GENERAL CHARACTERISTICS
1.2.1 Application This specification is applied to SS12F Silde Switch used for electronic equipment.
1.2.2 Operating temperature range -10℃ + 50℃
1.2.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature: 5~35℃
Relative humidity: 45~85%
Air pressure: 86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions Refer to individual product drawing.
1.4. Electrical specifications
NO.
Items
Test conditions
Criteria
1.4.1
Contact resistance
Measured at 1KHz small current (100mA or less)
30mΩ MAX
1.4.2
Insulation resistance
Apply a voltage of 500V DC for 1 MIN.
To following portions after which measurement shall be made.
(1)Between body and terminal.
(2) Between terminals.
100MΩ MIN
1.4.3
Dielectric strength
AC 500V rms(50-60Hz) for 1 min trip
Current:0.5mA
(1) Between terminals.
(2) Between individual terminal and frame.
Without damage to parts arcing or breakdown etc
1.5. Environment Resistance
NO.
Items
Test conditions
Criteria
1.5.1
Cold
After testing at 0±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.
There shall be no deformation or cracks in molded part.
1.5.2
Dry heat
After testing at 85±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h.
1.5.3
Damp heat
After testing at 40±2℃ and 90-95%RH for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.
1.5.4
Change of
temperature
After 5 cycles of following conditions the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.
1.6. WELDING CHARACTERISTICS
1.6.1
Solder ability test
The top of the terminals shall be dipped 2mm in the solder bath of 230±5℃ for 3±0.5 seconds.
The area of soldering should be over
75%
1.6.2
Resistance to soldering
Heat test
Soldering iron method:
Bit temperature 350±10℃
Application time of soldering iron 3±0.5 sec however excessive pressure shall not be applied to the terminal.
1.7. ENDURANCE
NO.
Item
Test condition
Criteria
1.7.1
Life test
Without load :
An actuator shall be subject to 10,000 cycles at a speed of 15 to 18 cycles for 1 min.
Contact resistance
200mΩ MAX
Insulation resistance
50 mΩ MIN
Withstand voltage 500VAC, AC 500V, 1 minute.AC 500V 1 Operating force±30% Initial value. Without damage to parts arcing or breakdown etc.
2. DRAWING & DIMENSION:
3. CIRCUIT & DIAGRAM:
1. PARTS LIST:
ITEM
PARTS
MATERIALS
QUANTITY
FINISH
1
KNOB
POM
1
BLACK
2
FRAME
STEEL STRIP
1
Ni PLATED
3
CASE
PHENOLIC RESIN
1
NATURAL
4
TERMINAL
BRASS STRIP
3
Ag PLATED
5
CONTACT
BRASS STRIP
1
Ag PLATED
6
SPRING
STEEL WIRE
1
NATURAL
2. PACKING:
2.1
Packing material:
Plastic bag
Double-layers paper cartonEPS
2.2
Packing number:
1000 pieces per bag
4 bag per inner carton
3 inner cartons per shipping cartonEach shipping carton 1200 pieces
2.3
Weight:
Gross Weight: 700g
Net Weight: 560g (500PCS)
2.4
Size:
X x X x X CM /XCBM