SK-SR-22D02G5SW-Cs DC 50V 0.3A 1P2T 3Pins Metal for Electronics

Series:SK-SR-22D02G5W-Cs

Description:

Type:              SK-SR-22D02G5W-Cs

Operation method:    Slide Switch

Comply with:          ■IP40  □IP65  □IP67  □IP68

Rating:               DC 50V 0.3A

Contact method:       1P2T  

Contact Now

  • Applications
  • Technical parameters
  • Remarks

1.Digital Products: digital camera, digital video and so on;   

2.Remote Control: the remote control of automobile domestic security products;   

3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;  
                                             
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ,refrigerator,washer;air-conditioning and so on;   
                                                                              
5.Security Products: visual interphone, monitor and so on;   
                      
6.Toys: electric toys and so on;   

7.Computer Products: PC camera and so on;   

8.Exercises Machines: treadmills, massage armchair and so on;                                                                    

9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
      
10.Others:  laser pen ,Pointer,Wireless mouse remote control pen,Laser projection pen,page turner,electronic pen;MousePen;overhead projector and so on;

11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders,automotive sets, etc.

12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine,  Music Instrument, etc.

1.1  GENERAL CHARACTERISTIC: 

1.1.1 Application   This specification is applied to SK22D Slide Switch used for electronic equipment.

1.1.2 Operating temperature range          -16℃ to 60℃

 

1.1.3 Test conditions                        

Unless other                                                               specified. The atmospheric conditions for making measurements and tests are as follows:

Ambient temperature:                             5~35℃

Relative humidity:                                45~85%

Air pressure:                       86~106kPa (860~1060 mbar)

Should any doubt arise in judgment. tests shall be conducted at the following conditions.

Ambient temperature:                             20±2℃

Relative humidity:                                60~70%

Air pressure:                      86~106kPa (860~1060 mbar)

 

1.2 Appearance construction and dimension: 

1.2.1 Appearance       

      Switch shall have good finishing, and no rust crack or plating failures.

1.2.2 Construction and dimensions    

     Refer to individual product drawing.

1.3. ELECTRICAL SPECIFICATION  

NO.

ITEM

TEST CONDITIONS

PERFORMANCE

1.3.1

CONTACT

RESISTANCE

MEASURED AT 1 KHz SMALL CURRENT(100 mA OR LESS)

100mΩ MAX

1.3.2

INSULATION

RESISTANCE

APPLY A VOLTAGE OF 500V DC SHALL BE APPLIED FOR 1 MIN AFTER

WHICH MEASUREMENT BE MADE:

(1) BETWEEN TERMINAL.

(2) BETWEEN INDIVIDUAL TERMINAL AND FRAME.

100MΩ MIN

1.3.3

DIELECTRIC

STRENGTH

AC 500V rms(50~60Hz) FOR 1 MIN TRIP CURRENT: 0.5 mA

(1) BETWEEN TERMINAL.

(2) BETWEEN INDIVIDUAL TERMINAL AND FRAME.

WITHOUT DAMAGE TO PARTS ARCING OR

BREAKDOWN ETC.

1.4. ENDURANCE 

NO.

ITEM

TEST CONDITIONS

PERFORMANCE

1.4.1

LIFE TEST

WITHOUT LOAD:

AN ACTUATOR SHALL BE SUBJECT TO 10,000 CYCLES AT A SPEED OF 15~18 CYCLES FOR 1 MIN.

(1) CONTACT RESISTANCE 200 mΩ MAX.

(2)INSULATION RESISTANCE 50MΩ MIN.

(3)WITHSTAND VOLTAGE AC 500V, 1 MINUTE.

(4)OPERATING FORCE ±30% INITIAL VALUE.

(5)WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC.

1.4.2

SOLDERA BILITY TEST

THE TOP OF THE TERMINALS SHALL BE DIPPED 2mm IN THE SOLDER BATH OF 260±5℃ FOR 3±0.5 SECONDS.

THE AREA OF SOLDERING SHOULD BE OVER 90%

1.4.3

RESISTANCE TO SOLDERING HEAT TEST

(1) TEMPERATURE AND IMMERSING TIME

 

TEMPERATURE(°C )

TIME(S)

MANUAL SOLDERING

350±10

3±0.5

(2) TMMERSION DEPTH:

IMMERSION DEPTH UP TO THE SURFACE OF THE BOARD THICKNESS OF PRINTED WIRING BOARD 1.6 mm.

WITHOUT DEFORMATION

OF CASE OR EXCESSIVE

LOOSENESS OF TERMINALS

MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL

BE SATISFIED.

1.4.4

HEAT TEST

THE JACK SHALL BE STORED AT A TEMPERATURE OF 70±2 °C FOR 48

HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED

RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT

SHALL BE MADE.SHALL BE MADE.

1.4.5

COLD TEST

THE SWITCH SHALL BE STORED AT A TEMPERATURE OF -25±3℃ FOR48HOURS.

THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE

1.5. WELDING PERFORMANCE 

NO.

ITEM

TEST CONDITIONS

PERFORMANCE

1.5.1

HUMIDITY TEST

THE JACK SHALL BE STORED AT A TEMPERATURE OF 40±2 °C AND A HUMIDITY OF 90% TO 95% FOR 96 Hr . THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES.

THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART.

 

1.5.2

STANDARD

ATMOSPHERIC

CONDITIONS

UNLESS OTHERWISE SPECIFIED.

THE STANDARD RANGE OF ATMOSPHERIC CONDITIONS FOR MAKING

MEASUREMENTS AND TESTS ARE AS FOLLOWS:

(1) AMBIENT TEMPERATURE : 5 °C TO 35 °C

(2) RELATIVE HUMIDITY : 45% TO 85%

(3) AIR PRESSURE : 86Kpa TO 106Kpa

1.5.3

PRACTICAL

TEMPERATURE

RANG

-16 °C ~ +60 °C

2. DRAWING & DIMENSION: 

 

3. PACKING: 

3.1

 Packing material:

 

Plastic bag 

3.2

 Packing number:

 200 pieces per bag
 3 inner cartons per shipping carton
 Each shipping carton 1000 pieces

3.3

Weight:

 Gross Weight:   24kg

 Net Weight  :   21kg

3.4

Size:

550 x 380 x 260 CM



1. PACKING: 

ITEM

PARTS

MATERIALS

QUANTITY

1

Frame

Steel strip, Ni plated

1

2

Knob

POM, Black

1

3

Base

Phenolic Resin ,Natural

1

4

Terminal

Brass strip, Ag plated

3

5

Spring plate  

PBS strip, Natural

1

6

Contact clip

PBS C5210R-EH, Ag Clad

1

return