RS1-10ASW1-1BB-60 2 pins ON-OFF SPST rocker switch for ECOVRCS vacuum cleaner robot
Series:RS1
Type: RS1-10ASW1-1BB-60
Construction category: D
Operation method: Rocker Action
Configuration: Single-Pole Single-Through (SPST)
Terminal form: #250 quick-connect Terminal
Mounting: Snap-In
Protection: IP40
- Applications
- Technical parameters
- Remarks
-
Home / Household Appliances
Electric kettle, Robot cleaner, Dust catcher, Vacuum cleaner, Coffee maker, Running machine etc.
Electronic Equipment
Toys, Power tools, Car control panel etc.
Medical Equipment
Communication Equipment
Automation Equipment
Automotive Electronics
Instrumentation
1.DETAIL SPECIFICATIONS:
Type:RS1-10ASW1-1BB-60
Construction category:D
Operation method:Rocker Action
Configuration:Single-Pole Single-Through (SPST)
Terminal form:#250 quick-connect Terminal
Mounting:Snap-In
Protection:IP40
1.1OPERATING CHARACTERISTICSCharacteristics
Units
Standards
Note
Actuating Force
N
3～7
Original 3～7
Contact Force
N
0.4 Min
Original 0.4 Min
Electrical Clearance
mm
3 Min
Original 3 Min
Note:
Actuating Force:The force required to move the actuator from the free to the operation position
1.2 GENERAL CHARACTERISTICS
1.2.1Application This specification is applied toRS1Rocker Switch used for electronic equipment.
1.2.2Operating temperature range 0℃ to 85℃
1.2.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure:86~106kPa (860~1060 mbar)
1.3Appearance construction and dimensions
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions Refer to individual product drawing.
1.4. Electrical specificationsNO.
Items
Test conditions
Criteria
1.4.1
Contact
resistance
Shall be measured
at 1A,5VDC by
voltage drop method
after some operations
without load.
Applied position:
Between terminal
and terminal
30mΩ MAX
1.4.2
Insulation
resistance
Test voltage:500VDC,
measured after 1 min
±5s
Applied position: 1)
Between terminal
and terminal
2)Between terminal
and ground
100MΩ MIN
1.4.3
Voltage
proof
Following test voltages
shall be applied for 1 min.
(Cut-off current:0.5mA)
1)Between terminal and
terminal :500VAC/min
(50~60Hz)
2)Between terminal and
ground: 1500VAC/min
(50~60Hz)
No dielectric
breakdown
shall occur
1.5. ENVIRONMENT RESISTANCE
NO.
Item
Test conditions
Criteria
1.5.1
Cold
After testing at 0±2℃
for 96 h, the switch
shall be allowed to
stand under normal
room temperature
and humidity condition
for 1h, and then
measurement shall be
made within 1 h. water
drops shall be removed.
Contact
resistance
(item 4.1):
100mΩ MAX
Insulation
resistance
(item 4.2):
50MΩ MIN
Voltage
proof:
(item 4.3)
No dielectric
breakdown
shall occur.
Operating
characteristic
(item 5.1):
Operating
characteristic
variety Within
±10% of
specified value .
No abnormalities
shall be
recognized in
appearance and
construction.
1.5.2
Dry heat
After testing at 85±2℃
for 96 h, the switch shall
be allowed to stand under
normal room temperature
and humidity condition for
1h, and then measurement
shall be made within 1 h.
1.5.3
Damp heat
After testing at 40±2℃ and
90-95%RH for 96 h, the
switch shall be allowed to
stand under normal room
temperature and humidity
condition for 1h, and then
measurement shall be
made within 1 h. water
drops shall be removed.
1.5.4
Change of
temperature
After 5 cycles of following
conditions the switch shall
be allowed to stand under
normal room temperature
and humidity condition for
1h, and then measurement
shall be made within 1 h.
water drops shall be
removed.
1.5.5
Salt mist
Switch shall be checked
after following lest.
1) Temperature: 35±2℃
2) Salt solution: 5±1%
(solids by mass)
3) Duration: 24±1h
After test, salt deposit shall
be removed in running water
No remarkable
corrosion shall
be recognized
in metal part
1.6. WELDING CHARACTERISTICS
1.6.1
Solder ability
Switch test under such
conditions and inspect after.
1）Variable temperature
range ：235±5℃；
2）Dip time：3±0.5s；
The area of dip
tin should
capture the 95%
impregnated area
1.6.2
Resistance to soldering heat
The switch will be inspect under
such conditions below
Temperature and impregnated time
Trial measure
temperature
（℃）
Time
（s）
Slot welding method
260±5
5±1
Soldering method
350±5
3±0.5
All of the
appearance,
motor functions,
electrical
properties are
no abnormal.
1.7. ENDURANCE
NO.
Item
Test condition
Criteria
1.7.1
Endurance
(According to
UL61058)
10.1 125VAC
Switch shall be operated according to
following sequence
(Test1~Test2)
Voltage
Current
Power
factor
Operation
rate
Number
of operation
Test1
120V
12.625A
0.75-0.8
6-10
cycles/min
50cycles
Test2
120V
10.1A
0.75-0.8
6-10
cycles/min
6000
cycles
Voltage proof(Cut-off current:0.5mA)
Test voltages shall be applied for 1 min
Insulation
resistance
(item 4.2):
50MΩ MIN
Voltage proof:
Terminal and
ground:1000VAC
No dielectric
breakdown
shall occur.
Operating
characteristic
(item 5.1):
Operating
characteristic
variety
Within10%,
-30%% of
specified value .
6000 cycles
temperature
rise:30℃ MAX;
No abnormalities
shall be
recognized in
appearance and
construction
1.7.2
Endurance
(According to
EN61058-1
/IEC61058-1)
10 3) A 250VAC
Switch shall be operated10,000 cycles at
15~20 cycles/min
Voltage proof(Cut-off current:0.5mA)
Test voltages shall be applied for 1 min.
Insulation
resistance
(item 4.2):
50MΩ MIN
Voltage proof:
Terminal and
terminal:750VAC
Terminal and
ground:1125VAC
No dielectric
breakdown
shall occur.
Operating
characteristic
(item 5.1):
Operating
characteristic
variety
Within ±30%
of specified value .
Temperature
rise:55℃ MAX
No abnormalities
shall be
recognized in
appearance and
construction
2. DRAWING & DIMENSION:
3. CIRCUIT DIAGRAM：
4. PACKING:
4.1
Packing material:
Plastic Tray /
Double-layers paper carton4.2
Packing number:
100 pieces per tray
10 trays per inner carton
4 inner cartons per shipping cartonEach shipping carton 4000 pieces
4.3
Weight:
Gross Weight: 16.35 kg
Net Weight: 15 kg
4.4
Size:
40 x 30 x 35 CM /0.052CBM
SAFETY APPROVAL & RATING:
Approved Rating
Mark
Reference No.
UL&CUL
VDE
10(3)250VAC T85
CQC
CQC09002040308
NEMKO
10(3)250VAC 20T85
SEMKO
10(3)250VAC T85
FIMKO
DEMKO
10(3)250VAC 20T85
CE
SH10050176-V1
10(3)250VAC T85
TUV
R50194721
ENEC
EK
CB
PARTS LIST:
ITEM
NAME
MATERIAL
1
Terminal
Brass alloy H65,Silver Plated
2
Terminal
Brass alloy H65,Silver Plated
3
Base
Plastic PA66
4
Button
Plastic PA66
5
Moving piece
Brass alloy H65,Silver Plated
6
Spring
Carbon spring steel thread,nickel plated
7
Steel ball
SUS304
8
Contact
AgNi10/Cu
9
Contact
AgNi10/Cu
Returned plastic should not exceed 20%.
Skype
QQ