Home » Products » Rocker Switch » Waterproof Rocker Switch

R13-11SW12F IP65 SPST waterproof illminated rocker switch with dust cover used for electronic fan

Series:R13

Description:

Type:                                  R13-11SW12F
Construction category: D
Operation method:         Rocker Action
Configuration:                 Single-Pole Single-Through (SPST)
Terminal form:                #187 quick-connect Terminal
Mounting:                        Snap-In
Protection:                       IP65

Contact Now

Applications
Technical parameters
Remarks

Home / Household Appliances Electric kettle, Robot cleaner, Dust catcher, Vacuum cleaner, Coffee maker, Running machine etc. Electronic Equipment Toys, Power tools, Car control panel etc. Medical Equipment Communication Equipment Automation Equipment Automotive Electronics Instrumentation

1.DETAIL SPECIFICATIONS:
Type:R13-11SW12F
Construction category:D
Operation method:Rocker Action
Configuration:Single-Pole Single-Through (SPST)
Terminal form:#187 quick-connect Terminal
Mounting:Snap-In
Protection:IP65
1.1OPERATING CHARACTERISTICS

Characteristics

Units

Standards

Note

Actuating Force

N

4±2 Max

Original 4±2

Contact Force

N

0.4 Min

Original 0.4 Min

Electrical Clearance

mm

3 Min

Original 3 Min

Note:
Actuating Force:The force required to move the actuator from the free to the operation position
1.2 GENERAL CHARACTERISTICS
1.2.1Application This specification is applied to R13-31 Rocker Switch used for electronic equipment.
1.2.2Operating temperature range 0~85℃
1.2.3Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure:86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions Refer to individual product drawing.
1.4. Electrical specifications

NO.

Items

Test conditions

Criteria

1.4.1

Contact

resistance

Shall be measured at

50VAC by voltage

drop method after

some operations

without load.

Applied position:

Between terminal

and terminal

35mΩ MAX

1.4.2

Insulation

resistance

Test voltage:500VDC,

measured after 1 min ±5s

Applied position: 1)Between

terminal and terminal

2)Between terminal and

ground

100MΩ MIN

1.4.3

Voltage

proof

Following test voltages shall

be applied for 1 min.

(Cut-off  current:0.5mA)

1)Between terminal and

terminal :1250VAC/min

(50~60Hz)

No dielectric

breakdown

shall occur

1.5. ENVIRONMENT RESISTANCE

NO.

Item

Test conditions

Criteria

1.5.1

Cold

After testing at -25±2℃

for 96 h, the switch shall

be allowed to stand under

normal room temperature

and humidity condition for

1h, and then measurement

shall be made within 1 h.

water drops shall be removed.

Contact

resistance

(item 4.1):

100mΩ MAX

Insulation

resistance

(item 4.2):

50MΩ MIN

Voltage proof:

(item 4.3)

No dielectric

breakdown

shall occur.

Operating

characteristic

(item 5.1):

Operating

characteristic

variety Within

±10% of

specified value .

No abnormalities

shall be

recognized in

appearance and

construction.

1.5.2

Dry

heat

After testing at 105±2℃ for

96 h, the switch shall be

allowed to stand under normal

room temperature and humidity

condition for 1h, and then

measurement shall be made

within 1 h.

1.5.3

Damp

heat

After testing at 40±2℃ and

90-95%RH for 96 h, the

switch shall be allowed to

stand under normal room

temperature and humidity

condition for 1h, and then

measurement shall be made

within 1 h. water drops shall

be removed.

3.5.4

Change

of

temperature

After 20 cycles of following

conditions the switch shall

be allowed to stand under

normal room temperature

and humidity condition for

1h, and then measurement

shall be made within 1 h.

water drops shall be

removed.

1.5.5

Salt mist

Switch shall be checked

after following lest.

1) Temperature: 35±2℃

2) Salt solution: 5±1%

(solids by mass)

3) Duration: 24±1h

After test, salt deposit

shall be removed

in running water

No remarkable

corrosion shall

be recognized

in metal part

1.6. WELDING CHARACTERISTICS

1.6.1

Solder ability

Switch test under such conditions and

inspect after.

1）Variable temperature range ：235±5℃；

2）Dip time：3±0.5s；

The area of

ip tin should

capture the

95%

impregnated

area

1.6.2

Resistance to

soldering heat

The switch will be inspect under such

conditions below

Temperature and impregnated time

Trial measure

temperature

（℃）

Time（s）

Slot welding method

260±5

5±1

Soldering method

350±5

3±0.5

All of the

appearance,

motor functions,

electrical

properties are

no abnormal.

1.7. ENDURANCE

NO.

Item

Test condition

Criteria

1.7.1

Endurance

(According to

UL61058)

12A 125VAC

Switch shall be operated according to

following sequence

(Test1~Test2)

Voltage

Current

Power

factor

Operation

rate

Number

of operation

Test1

125V

14A

0.75-0.8

6-10

cycles/min

50cycles

Test2

125V

12A

0.75-0.8

6-10

cycles/min

6000cycles

Voltage proof(Cut-off current:0.5mA)

1GPA 125/250VAC ;

Switch shall be operated 6,000 cycles at

15-20 cycles/min.

Test voltages shall be applied for 1 min

Insulation

resistance

(item 4.2):

30MΩ MIN

Voltage proof:

Terminal and

ground:1000VAC

No dielectric

breakdown

shall occur.

Operating

characteristic

(item 5.1):

Operating

characteristic

variety

Within ±20%

of specified value .

6000 cycles

temperature

rise:30℃ MAX;

10,000 cycles

temperature

rise:55℃ MAX;

No abnormalities

shall be recognized

in appearance and

construction

1.7.2

Endurance

(According to

EN61058-1

/IEC61058-1)

6 A 250VAC

Switch shall be operated 10,000 cycles at

15~20 cycles/min

Voltage proof(Cut-off current:0.5mA)

Test voltages shall be applied for 1 min.

Insulation

resistance

(item 4.2):

50MΩ MIN

Voltage proof:

Terminal and

terminal:750VAC

Terminal and

ground:1500VAC

No dielectric

breakdown

shall occur.

Operating

characteristic

(item 5.1):

Operating

characteristic

variety

Within ±20%

of specified

value .

Temperature

rise:55℃ MAX

No abnormalities

shall be

recognized in

appearance and

construction

2. DRAWING & DIMENSION:

3. CIRCUIT DIAGRAM：

4.1

Packing material:

Plastic bag /
Double-layers

paper carton

4.2

Packing number:

200 pieces per bag
10 bags per inner

carton
3 inner cartons per

shipping carton

1 shipping carton

6000 pieces

4.3

Weight:

Gross Weight: 26 kg

Net Weight: 24.5 kg

4.4

Size:

57*27*32CM /0.049248CBM

Approved Rating	Mark	Reference No.
10(6)A 125/250VAC	UL&CUL	E256173
12(8)A 250VAC	VDE	0630-1
12(8)A 250VAC	CQC	CQC09002039559
	NEMKO
	SEMKO
	FIMKO
	DEMKO
	CE
	TUV
	ENEC
	EK
	CB

ITEM	NAME	MATERIAL
1	Button	Plastic
2	Base	Plastic
3	Terminal	Brass alloy H65,Silver Plated
4	Plate moving	Brass alloy H65,Silver Plated
5	Contact	Silver-Cadmium Oxide alloy
6	Contact	Silver-Cadmium Oxide alloy
7	Spring	Manganese Steel
8	Steel Ball	Stainless Steel
9	Light	Neon

Language

R13-11SW12F IP65 SPST waterproof illminated rocker switch with dust cover used for electronic fan

Products list

Micro Switch

Rocker Switch

Tactile Switch

Push Button Switch

Slide Switch

Toggle Switch

Dip Switch

Socket

pressure switch

Characteristics	Units	Standards	Note
Actuating Force	N	4±2 Max	Original 4±2
Contact Force	N	0.4 Min	Original 0.4 Min
Electrical Clearance	mm	3 Min	Original 3 Min

NO.	Items	Test conditions	Criteria
1.4.1	Contact resistance	Shall be measured at 50VAC by voltage drop method after some operations without load. Applied position: Between terminal and terminal	35mΩ MAX
1.4.2	Insulation resistance	Test voltage:500VDC, measured after 1 min ±5s Applied position: 1)Between terminal and terminal 2)Between terminal and ground	100MΩ MIN
1.4.3	Voltage proof	Following test voltages shall be applied for 1 min. (Cut-off current:0.5mA) 1)Between terminal and terminal :1250VAC/min (50~60Hz)	No dielectric breakdown shall occur

4.1	Packing material:	Plastic bag / Double-layers paper carton
4.2	Packing number:	200 pieces per bag 10 bags per inner carton 3 inner cartons per shipping carton 1 shipping carton 6000 pieces
4.3	Weight:	Gross Weight: 26 kg Net Weight: 24.5 kg
4.4	Size:	572732CM /0.049248CBM

NO.	Item	Test conditions	Criteria
1.5.1	Cold	After testing at -25±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.	Contact resistance (item 4.1): 100mΩ MAX Insulation resistance (item 4.2): 50MΩ MIN Voltage proof: (item 4.3) No dielectric breakdown shall occur. Operating characteristic (item 5.1): Operating characteristic variety Within ±10% of specified value . No abnormalities shall be recognized in appearance and construction.
1.5.2	Dry heat	After testing at 105±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h.
1.5.3	Damp heat	After testing at 40±2℃ and 90-95%RH for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.
3.5.4	Change of temperature	After 20 cycles of following conditions the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.
1.5.5	Salt mist	Switch shall be checked after following lest. 1) Temperature: 35±2℃ 2) Salt solution: 5±1% (solids by mass) 3) Duration: 24±1h After test, salt deposit shall be removed in running water	No remarkable corrosion shall be recognized in metal part

Language

R13-11SW12F IP65 SPST waterproof illminated rocker switch with dust cover used for electronic fan

Follow us