PB12-2-M illuminated LED green momentary push button switch with 4 pins
Series:PB12 series
Type: PB12-2-M
Construction category: D Tyoe
Operation method: Push button switch
Configuration: Single-Pole Single -Throw (SPST)
Terminal form: Solder Terminal
Mounting:
Protection: IP55
Ratings: 2 A 250VAC 0.1A 24VDC
- Applications
- Technical parameters
- Remarks
-
Enormous remote
controller and portable remote controller
Instrumentation
Medical equipment
Telecommunications and networking equipment
Computers & peripherals
Instrumentation and controls
Industrial electronic equipment
Industrial remote controller
Medical Equipment
Communication
Outdoor Controls
Public building, Home security, Business building, Industrial equipment…etc.
3. DETAIL SPECIFICATIONS
Type:PB12-2-M
Construction category: D
Operation method: Push button switch
Configuration:Single-Pole Single -Throw (SPST)
Terminal form:Solder Terminal
Mounting:
Protection: IP55
Ratings 2 A 250VAC 0.1A 24VDC
Withstand voltage 1000VAC,1Min
3.1 General
3.1.1 Application This specification is applied to KAN-J4 Power Switch used for electronic equipment.
3.1.2 Operating temperature range 0℃ to +125℃
3.1.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure:86~106kPa (860~1060 mbar)
3.2Appearance construction and dimensions
3.2.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
3.2.2Construction and dimensions Refer to individual product drawing.
3.3. Electrical Characteristics
NO.
Items
Test conditions
3.3.1
Contact resistance
The contact resistance should be 50mΩ(Max).
3.3.2
Insulation resistance
It is measured with 500V DC 1minute should be 100MΩ(Min).
3.3.3
Dielectric strength
AC 2000V,1min.(before endurance test)
AC 1500V,1min.(after endurance test)
3.4 Mechanical Characteristics
Item
Description
Test Conditions
1
Operating Force
400gf±150
2
Operating Life
The mechanical life all of 30 000 cycles
3
Contact Spacing
Min. 3.0mm (IEC61058)
3.5Durability
NO.
Item
Test condition
Criteria
3.5.1
Endurance
(According to
UL61058)
2A 250VAC 0.1A 24VDC
Switch shall be operated
according to following sequence
(Test1~Test2)Voltage proof(Cut-offVoltage
Current
Power
factorOperation
rateNumber
of operationTest1
250V
2A
0.75-0.8
6-10
cycles/min
50cycles
Test2
250V
2A
0.75-0.8
6-10
cycles/min
6000cycles
current:0.5mA)
2A 250VAC 0.1A 24VDC
Switch shall be operated
50,000 cycles at 15-20 cycles/min.
Test voltages shall be
applied for 1 minInsulation
resistance(item 4.2):50MΩ MIN
Voltage proof:
Terminal and ground:
1000VAC
No dielectric
breakdown shall occur.
Operating characteristic
(item 5.1):
Operating characteristic
variety
Within ±20% of
specifiedvalue .
6000 cycles temperature
rise:45℃MAX;
10,000 cycles
temperature rise:55℃ MAX;
No abnormalities shall be
recognized in appearance
and construction3.5.2
Endurance
(According to EN61058-1
/IEC61058-1)
2A 250VAC 0.1A 24VDC
Switch shall be operated
50,000 cycles at 15~20 cycles/minVoltage proof(Cut-off current:0.5mA)
Test voltages shall be applied for 1 min.
Insulation resistance(item 4.2):
50MΩ MIN
Voltage proof:
Terminal and terminal:750VAC
Terminal and ground:1500VAC
No dielectric breakdown shall occur.
Operating characteristic (item 5.1):
Operating characteristic variety
Within ±20% of specifiedvalue .
Temperature rise:55℃ MAX
No abnormalities shall be
recognized in appearance
and construction
3.6. SOLDERING
Solder ability and Resistance to sold heat according to IEC 68-2-20
4. DRAWING & DIMENSION
SAFETY APPROVAL & RATING:
Approved Rating
Mark
Reference No.
UL&CUL
VDE
CQC
5. PARTS LIST:NO.
quantity
Items
Material
1
1
cap
PA66
2
1
Nut
Brass, NI plated
3
1
Base
PA66,UL rated:94V-2 Min
4
1
Terminal
Copper, silver plated
Note: Returned plastic should not exceed 20%.
Skype
QQ