MS22D16G2SW-B (unilateral) DC 50V 0.3A 1P2T 3Pins Metal for Electronics
Series:MS22D16G2SW-B (unilateral)
Type: MS22D16G2SW-B (unilateral)
Operation method: Slide Switch
Comply with: ■IP40 □IP65 □IP67 □IP68
Rating: DC 50V 0.3A
Contact method: 1P2T
- Applications
- Technical parameters
- Remarks
-
1.Digital Products: digital camera, digital video and so on;
2.Remote Control: the remote control of automobile domestic security products;
3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ，refrigerator，washer;air-conditioning and so on;
5.Security Products: visual interphone, monitor and so on;
6.Toys: electric toys and so on;
7.Computer Products: PC camera and so on;
8.Exercises Machines: treadmills, massage armchair and so on;
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
10.Others: laser pen ，Pointer，Wireless mouse remote control pen，Laser projection pen，page turner，electronic pen；MousePen；overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders，automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.
1.1 GENERAL CHARACTERISTIC:
1.1.1 Application This specification is applied to MS22 Slide Switch used for electronic equipment.
1.1.2 Operating temperature range -16℃ to 60℃
1.1.3 Test conditions
Unless other specified. The atmospheric conditions for making measurements and tests are as follows:
Ambient temperature: 5~35℃
Relative humidity: 45~85%
Air pressure: 86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature: 20±2℃
Relative humidity: 60~70%
Air pressure: 86~106kPa (860~1060 mbar)
1.2 Appearance construction and dimension:
1.2.1 Appearance
Switch shall have good finishing, and no rust crack or plating failures.
1.2.2 Construction and dimensions
Refer to individual product drawing.
1.3. ELECTRICAL SPECIFICATION
NO.
ITEM
TEST CONDITIONS
PERFORMANCE
1.3.1
CONTACT
RESISTANCE
MEASURED AT 1 KHz SMALL CURRENT(100 mA OR LESS)
100mΩ MAX
1.3.2
INSULATION
RESISTANCE
APPLY A VOLTAGE OF 500V DC SHALL BE APPLIED FOR 1 MIN AFTER
WHICH MEASUREMENT BE MADE:
(1) BETWEEN TERMINAL.
(2) BETWEEN INDIVIDUAL TERMINAL AND FRAME.
100MΩ MIN
1.3.3
DIELECTRIC
STRENGTH
AC 500V rms(50~60Hz) FOR 1 MIN TRIP CURRENT: 0.5 mA
(1) BETWEEN TERMINAL.
(2) BETWEEN INDIVIDUAL TERMINAL AND FRAME.
WITHOUT DAMAGE TO PARTS ARCING OR
BREAKDOWN ETC.
1.4. ENDURANCE
NO.
ITEM
TEST CONDITIONS
PERFORMANCE
1.4.1
LIFE TEST
WITHOUT LOAD:
AN ACTUATOR SHALL BE SUBJECT TO 10,000 CYCLES AT A SPEED OF 15~18 CYCLES FOR 1 MIN.
（1） CONTACT RESISTANCE 200 mΩ MAX.
（2）INSULATION RESISTANCE 50MΩ MIN.
（3）WITHSTAND VOLTAGE AC 500V, 1 MINUTE.
（4）OPERATING FORCE ±30% INITIAL VALUE.
（5）WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC.
1.4.2
SOLDERA BILITY TEST
THE TOP OF THE TERMINALS SHALL BE DIPPED 2mm IN THE SOLDER BATH OF 260±5℃ FOR 3±0.5 SECONDS.
THE AREA OF SOLDERING SHOULD BE OVER 90%
1.4.3
RESISTANCE TO SOLDERING HEAT TEST
(1) TEMPERATURE AND IMMERSING TIME
TEMPERATURE（°C ）
TIME（S）
MANUAL SOLDERING
350±10
3±0.5
(2) TMMERSION DEPTH:
IMMERSION DEPTH UP TO THE SURFACE OF THE BOARD THICKNESS OF PRINTED WIRING BOARD 1.6 mm.
WITHOUT DEFORMATION
OF CASE OR EXCESSIVE
LOOSENESS OF TERMINALS
MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL
BE SATISFIED.
1.4.4
HEAT TEST
THE JACK SHALL BE STORED AT A TEMPERATURE OF 70±2 °C FOR 48
HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED
RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT
SHALL BE MADE.SHALL BE MADE.
1.4.5
COLD TEST
THE SWITCH SHALL BE STORED AT A TEMPERATURE OF -25±3℃ FOR48HOURS.
THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE
1.5. WELDING PERFORMANCE
NO.
ITEM
TEST CONDITIONS
PERFORMANCE
1.5.1
HUMIDITY TEST
THE JACK SHALL BE STORED AT A TEMPERATURE OF 40±2 °C AND A HUMIDITY OF 90% TO 95% FOR 96 Hr . THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 Hr FOR OTHER PROCEDURES.
THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART.
1.5.2
STANDARD
ATMOSPHERIC
CONDITIONS
UNLESS OTHERWISE SPECIFIED.
THE STANDARD RANGE OF ATMOSPHERIC CONDITIONS FOR MAKING
MEASUREMENTS AND TESTS ARE AS FOLLOWS:
(1) AMBIENT TEMPERATURE : 5 °C TO 35 °C
(2) RELATIVE HUMIDITY : 45% TO 85%
(3) AIR PRESSURE : 86Kpa TO 106Kpa
1.5.3
PRACTICAL
TEMPERATURE
RANG
-16 °C ~ +60 °C
2. DRAWING & DIMENSION:
3. PACKING:
3.1
Packing material:
Plastic bag
3.2
Packing number:
200 pieces per bag
3 inner cartons per shipping carton
Each shipping carton 1000 pieces3.3
Weight:
Gross Weight: 24kg
Net Weight : 21kg
3.4
Size:
550 x 380 x 260 CM
1. PACKING:
1.1
Packing material:
Plastic bag
1.2
Packing number:
200 pieces per bag
3 inner cartons per shipping carton
Each shipping carton 1000 pieces1.3
Weight:
Gross Weight: 24kg
Net Weight : 21kg
1.4
Size:
550 x 380 x 260 CM
Skype
QQ