MS10-01ZSW0-C015-08 Mini Snap Action Switch replace Omron/Panasonic/ Cherry
Series:MS10 series
Type:MS10-01ZSW0-C015-08
Construction category:D type
Operation method:Snap Action
Configuration:Single-Pole Double -Throw (SPDT)
Terminal form:#250 Quick-connect Terminal
Mounting:via side mounting holes
Protection:IP40
- Applications
- Technical parameters
- Remarks
-
Widely used in home appliance, electronic equipment, automatic machine,
communication equipment, car electron, apparatus and instrument, electric motion tool etc.
Electric Heating Faucet
Shredder
Baby chair
CNC machine tools
Power generator
Test equipment
Power tools
Air conditioner
Water heater control panel
Bathroom products
Vacuum cleaner
Kitchen products
Range hood machine
Microwave oven
Pass-through machine
3.DETAIL SPECIFICATIONS
Type:MS10-01ZSW0-C015-08
Construction category:D type
Operation method:Snap Action
Configuration:Single-Pole Double -Throw (SPDT)
Terminal form:#250 Quick-connect Terminal
Mounting:via side mounting holes
Protection:IP40
3.1OPERATING CHARACTERISTICSCharacteristics
Units
Standards
Note
Actuating Force
N
0.15 Max
Original 0.15 Max
Release Force
N
0.15 Min
Original 0.15 Min
Operating Position
mm
14.6 ± 0.5
Original 14.6 ± 0.5
Note:
Actuating Force:
The force required to move the actuator from the free to the operation position
Release Force
The force allowed the mechanism to reset actuator after operation
Free Position
The position of the actuator when no external force is applied
Operating Position
The position of the actuator when contact change-over take place
Movement Differential
The distance between operation and release position
3.2 General
3.2.1 Application This specification is applied to KW10 Micro Switch used for electronic equipment.
3.2.2 Operating Temperature range -25℃ ～ +105℃
3.2.3 Test condition Unless otherwise specified. The atmospheric conditions for making measurementsAnd tests are as follows:
Ambient temperature: 15~35℃
Relative humidity: 45~85%
Air pressure: 86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. It shall be conducted at the following conditions.
Ambient Temperature: 20±2℃
Relative humidity: 60~70%
Air pressure: 86~106kPa (860~1060 mbar)
3.3 Appearance Construction and Dimension
3.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
3.3.2construction and dimensions Refer to individual product drawing.
3.4. Electrical SpecificationsNO.
Item
Test Condition
Criteria
3.4.1
Contact
Resistance
Shall be measured at 1A,5V DC by voltage
drop method after some operations
without load.
Applied position: Between terminal “C” and terminal “NO”.
50mΩ MAX
3.4.2
Insulation
Resistance
Test voltage:500VDC, measured after 1 min ±5s
Applied Position: applied position:
1)Between terminal “C” and terminal “NO”2)Between terminal and ground
100MΩ MIN
3.4.3
Voltage
proof
Following test voltages shall be applied for 1 min.
1)Between terminal “C” and terminal
“NO”:1000VAC (50~60Hz)
2)Between terminal and ground: 1500V AC(50~60Hz)
No dielectric
breakdown shall
occur
3.5. Durability
NO.
Item
Test Condition
Criteria
3.5.1
Cold
After testing at -25±2℃ for 96 h,
the switch shall be allowed to stand
under normal room temperature
and humidity condition for 1h, and
then measurement shall be made
within 1 h. water drops shall be
removed.
Contact
resistance
(item 4.1):
100mΩ
MAX
Insulation
resistance
(item 4.2):
50MΩ MIN
Voltage
proof:
(item 4.3)
No dielectric
breakdown
shall occur.
Within 10%
of specified
value .No
abnormalities
shall be
recognized
in
appearance
and
construction
3.5.2
Dry heat
After testing at 105±2℃ for 96 h,
the switch shall be allowed to stand
under normal room temperature
and humidity condition for 1h, and
then measurement shall be made
within 1 h.
3.5.3
Damp Heat
After testing at 40±2℃ and
90-95%RH for 96 h, the switch shall be
allowed to stand under normal
room temperature and humidity
condition for 1h, and then
measurement shall be made within 1 h.
water drops shall be removed.
3.5.4
Change of Temperature
After 5 cycles of following conditions
the switch shall be allowed
to stand under normal room
temperature and humidity condition
for 1h, and then measurement
shall be made within 1 h. water
drops shall be removed.
3.6 Durability
NO.
Item
Test Condition
Criteria
3.6.1
Endurance
(According to
UL61058)
1/2hp 125VAC
Switch shall be operated according to following sequence
(Test1~Test2)
Voltage
Current
Power
Factor
Operation
Rate
Operation
Cycles
Test 1
125V
58.8 A
0.4-0.5
6-10Cycles/min
50cycles
Test2
125V
4.9 A
0.7-0.8
6-10Cycles/min
50000cycles
Voltage proof：Test voltage shall be applied for
1 min（50~60Hz, Cut-off current:0.5mA)
10GPA 125/250VAC; 6A 30VDC
Operation Cycles：50,000 次 ；
Operation Frequency：15~20 次/min
Voltage proof：Test voltage shall be applied for
1 min（50~60Hz, Cut-off current:0.5mA)
Insulation
resistance
(item 4.2):
50MΩ MIN；
Voltage proof:
Terminal and
terminal:
1000VAC
No dielectric
breakdown
shall occur.
Operating
characteristic
(item 5.1):
Within 20%
of specified
value .6000 cycles
temperature
rise: 30℃
MAX；
10000cycles
temperature
rise: 55℃
MAX；
No
abnormalities
shall be
recognized in
appearance
and
construction.
3.6.2
Endurance
(According
to EN61058-1
/IEC61058-1)
10(3)A 125/250VAC; 6A 30VDC
Operating Cycles：50,000 cycles
Operation Frequency：15~20 cycles/m 3(0.5)A 250VAC
Voltage proof：Test voltage shall be applied for
1 min（50~60Hz, Cut-off current:0.5mA)
Insulation
resistance
(item 4.2):
50MΩ MIN
Voltage proof:
Terminal
and terminal:
750VAC
Terminal
and ground:
1125VAC
No dielectric
breakdown
shall occur.
Operating
characteristic
(item 5.1):
Within ±20%
of specified
value .Temperature
rise:55℃ MAX
No
abnormalities
shall be
recognized
in appearance
and
construction
4. DRAWING & DIMENSION
5. CIRCUIT DIAGRAM
7. PACKING:
7.1
Packing material:
Plastic box /
Double-layers paper carton7.2
Packing number:
100 pieces per box
4 inner cartons per shipping carton
Each shipping carton 10000 pieces7.3
Weight:
Gross Weight: 8.5kg
Net Weight: 7.0kg
7.4
Size:
31.0 x 25.0 x 34.5 CM / 0.045CBM
SAFETY APPROVAL & RATING:
Approved Rating
Mark
Reference No.
1A125/250VAC 1/8hp125/250VA 1E4 T125 1(0.3) A, 125/250 VAC 1GP A, 125/250 VAC
UL&CUL
E 176213
VDE
1(0.3)A 125V/250VAC 5E4 25T105
CQC
CQC10002048742
NEMKO
SEMKO
FIMKO
1(0.3)A, 125/250 VAC 1 A, 30 V dc; 50-60Hz, 5E4, 25T105, IP40
DEMKO
D-00720
CE
TUV
1(0.3)A, 125/250 VAC 1 A, 30 V dc; 50-60Hz, 5E4, 25T105, IP40
ENEC
ENEC-00183
EK
1(0.3)A, 125/250 VAC 1 A, 30 V dc; 50-60Hz, 5E4, 25T105, IP40
CB
DK-5193
6. PARTS LIST
NO.
Item
Material
1
Cover
Plastic PA66 Black
2
Terminal
Brass alloy H65, Silver
3
Terminal
Brass alloy H65, Silver
4
Case
Plastic PA66 Black
5
Contact
AgNi10/Cu, Gold plated
6
Contact
AgNi10/Cu, Gold plated
7
Plate moving
Beryllium Bronze C1720 HM
8
Terminal
Brass alloy H65, Silver
9
Button
Plastic PA66
10
Spring
Stainless steel SUS304H
Note: Returned plastic should not exceed 20%.
Skype
QQ