MPS-16SW-ST 16mm flat head stainless steel pushbutton switch with brass terminal
Series:MPS-16SW
Type: MPS-16SW-ST
Construction category: D type
Operation method: Push button switch
Configuration: Single-Pole Single -Throw (SPST)
Terminal form: Solder Terminal
Protection: IP65
Ratings: 3A 36VDC
Withstand voltage: 1000VAC,1Min
- Applications
- Technical parameters
- Remarks
-
Enormous remote
controller and portable remote controller
Instrumentation
Medical equipment
Telecommunications and networking equipment
Computers & peripherals
Instrumentation and controls
Industrial electronic equipment
Industrial remote controller
Medical Equipment
Communication
Outdoor Controls
Public building, Home security, Business building, Industrial equipment…etc.
3. DETAIL SPECIFICATIONS:
Type:MPS-16SW-ST
Construction category: D
Operation method: Push button switch
Configuration: Single-Pole Single -Throw (SPST)
Terminal form:Solder Terminal
Protection:IP65
Ratings 3A 36VDC
Withstand voltage 1000VAC,1Min
3.1 General
3.1.1 Application This specification is applied to KAN-J4 Power Switch used for electronic equipment.
3.1.2 Operating temperature range -20℃ to +55℃
3.1.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure: 86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure: 86~106kPa (860~1060 mbar)
3.2Appearance construction and dimensions
3.2.1Appearance Switch shall have good finishing, and no rust crack or plating failures.
3.2.2Construction and dimensions Refer to individual product drawing3.3. Electrical Characteristics
NO.
Items
Test conditions
3.3.1
Contact resistance
The contact resistance should be 50mΩ(Max).
3.3.2
Insulation resistance
It is measured with 500V DC 1minute should be 1000MΩ(Min).
3.3.3
Dielectric strength
AC 1000V,1min.(before endurance test)
AC 1000V,1min.(after endurance test)
3.4 Mechanical Characteristics
Item
Description
Test Conditions
1
Operating Force
450gf-100gf
2
Operating Life
The mechanical life all of 50 000 cycles
3
Contact Spacing
Min. 3.0mm (IEC61058)
3.5Durability
NO.
Item
Test condition
Criteria
3.5.1
Endurance
(According to
UL61058)
3A 36VDC
Switch shall be
operated according
to following sequence
(Test1~Test2)Voltage
Current
Power factor
Operation rate
Number of operation
Test1
36VDC
0.3A
0.75-0.8
6-10
cycles/min
50cycles
Test2
36VDC
0.3A
0.75-0.8
6-10
cycles/min
6000cycles
Voltage proof(Cut-off current:0.5mA)
3A 36VDC
Switch shall be operated 50,000 cycles at 15-20 cycles/min.
Test voltages shall be applied for 1 min
Insulation resistance(item 4.2):
50MΩ MIN
Voltage proof:
Terminal and ground:1000VAC
No dielectric breakdown shall occur.
Operating characteristic (item 5.1):
Operating characteristic variety
Within ±20% of specifiedvalue .
6000 cycles temperature rise:45℃MAX;
10,000 cycles temperature rise:55℃ MAX;No abnormalities shall be recognized in appearance and construction
3.5.2
Endurance
(According to EN61058-1
/IEC61058-1)
2A 36VDC
Switch shall be operated 50,000 cycles at 15~20 cycles/min
Voltage proof(Cut-off current:0.5mA)
Test voltages shall be applied for 1 min.
Insulation resistance(item 4.2):
50MΩ MIN
Voltage proof:
Terminal and terminal:750VAC
Terminal and ground:1500VACNo dielectric breakdown shall occur.
Operating characteristic (item 5.1):
Operating characteristic variety
Within ±20% of specifiedvalue .
Temperature rise:55℃ MAX
No abnormalities shall be recognized in appearance and construction
3.6. SOLDERING
Solder ability and Resistance to sold heat according to IEC 68-2-20
4. DRAWING & DIMENSION:
PARTS LIST:
NO.
quantity
Items
Material
1
1
terminal
Brass sliver or Golden plated
2
1
Base
PC
3
1
Button base
PBT,UL rated 94V-0
4
1
Contact
Ag ally
5
1
actuator
PC/Stainless Steel
Note: Returned plastic should not exceed 20%.
Skype
QQ