KW10-ZSW6P150-08 Mini Snap Action Switch with Arc Zippy Equivalent

Series:

Description:

Type:KW10-ZSW6P150-08
Construction category:D type
Operation method:Snap Action
Configuration:Single-Pole Double -Through (SPDT)
Terminal form:PCB Terminal
Mounting:via side mounting holes
Protection:Comply with IP40

Contact Now

  • Applications
  • Technical parameters
  • Remarks

Widely used in home appliance, electronic equipment, automatic machine,
communication equipment, car electron, apparatus and instrument, electric motion tool etc.

Baby chair
CNC machine tools
Power generator
Test equipment

Power tools
Air conditioner
Water heater control panel
Bathroom products


1.DETAIL SPECIFICATIONS:
  Type:KW10-ZSW6P150-08
  Construction category:D type
  Operation method:Snap Action
  Configuration:Single-Pole Double -Through (SPDT)
  Terminal form:PCB Terminal
  Mounting:via side mounting holes
  Protection:Comply with IP40
1.1OPERATING CHARACTERISTICS

Characteristics

Units

Standards

Note

Actuating Force

N

0.36 Max

Original 0.36 max.

Release Force

N

0.05 Min

Original 0.05 Min

Operating Position

mm

9.5 ± 1.0

Original 9.5 ± 1.0

Note:
Actuating Force:
The force required to move the actuator from the free to the operation position
Release Force
The force allowed the mechanism to reset actuator after operation
Free Position
The position of the actuator when no external force is applied
Operating Position
The position of the actuator when contact change-over take place
Movement Differential
The distance between operation and release position           

1.2 General
1.2.1 Application This specification is applied to KW10 Micro Switch used for electronic equipment.
1.2.2 Operating Temperature range -40℃ ~ +85℃
1.2.3 Test condition Unless otherwise specified. The atmospheric conditions for making measurements And tests are as follows:
Ambient temperature: 15~35℃
Relative humidity: 45~85%
Air pressure: 86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. It shall be conducted at the following conditions.
Ambient Temperature: 20±2℃
Relative humidity: 60~70%
Air pressure: 86~106kPa (860~1060 mbar)
1.3 Appearance Construction and Dimension
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2construction and dimensions Refer to individual product drawing.
1.4. Electrical Specifications

NO.

Item

Test Condition

Criteria

1.4.1

Contact Resistance

Shall be measured at 1A,5V DC 

by voltage drop 

method after some operations 

without load.

Applied position: Between terminal 

“C” and terminal “NO”.

50mΩ MAX

1.4.2

Insulation Resistance

Test voltage:500VDC, measured 

after 1 min ±5s

Applied Position: applied position: 
1)Between terminal “C” and 

terminal “NO”

2)Between terminal and ground

100MΩ MIN

1.4.3

Voltage proof

Following test voltages shall be 

applied for 1 min.

1)Between terminal “C” and 

terminal “NO”:600VAC (50~60Hz)

2)Between terminal and 

ground: 1000V AC(50~60Hz)

No dielectric 

breakdown 

shall occur

1.5. Durability

NO.

Item

Test Condition

Criteria

1.5.1

Cold

After testing at -40±2℃ for 96 h, 

the switch shall be allowed to stand 

under normal room temperature 

and humidity condition for 1h, and then 

measurement shall be made within 

1 h. water drops shall be removed.

Contact 

resistance

(item 4.1): 

100mΩ MAX

Insulation 

resistance 

(item 4.2):

50MΩ MIN

Voltage proof: 

(item 4.3)

No dielectric 

breakdown 

shall occur.

Within 10%

 of specified
value .

No abnormalities 

shall be recognized 

in appearance and 

construction

 

1.5.2

Dry heat

After testing at 85±2℃ for 96 h, the 

switch shall be allowed to stand under

 normal room temperature and humidity 

condition for 1h, and then 

measurement shall be made within 1 h.

1.5.3

Damp Heat

After testing at 40±2℃ and 90-95%RH 

for 96 h, the switch shall be 

allowed to stand under normal room 

temperature and humidity 

condition for 1h, and then measurement

 shall be made within 1 h. 

water drops shall be removed.

1.5.4

Change of

 Temperature

After 5 cycles of following conditions 

the switch shall be allowed to 

stand under normal room temperature 

and humidity condition for 1h, 

and then measurement shall be made 

within 1 h. water drops shall be 

removed.

1.5.5

Salt Mist

Switch shall be checked 

after following lest.

1) Temperature: 35±2℃

2) Salt solution: 5±1% 

(solids by mass)

3) Duration: 24±1h

After test, salt deposit shall 

be removed in running water

 

No remarkable 

corrosion shall 

be recognized in 

metal part

1.6. Welding Performance

 

1.6.1

 

Solder ability

Switch test under such conditions 

and inspect after. 

1Variable temperature 

range :235±5℃

2Dip time:3±0.5s

 

The area of dip 

tin should 

capture the 95% 

impregnated area

 

1.6.2

 

Resistance to

 soldering heat

 

The switch will be inspect under such 

conditions below

        Temperature and impregnated time

Trial measure

temperature(

Time(s

Slot welding method

260±5

5±1

Soldering method

350±5

3±0.5

 

 

 

All of the 

appearance, 

motor functions, 

electrical 

properties are 

no abnormal. 

1.7.  Durability

NO.

Item

Test Condition

Criteria

 

1.7.1

 

Endurance

(According to

 UL61058)

1A 125VAC

Switch shall be operated according to following sequence

(Test1~Test2)

 

Voltage

Current

Power

 Factor

Operation

 Rate

Operation 

Cycles

Test 1

125V

4.5A

0.75-0.8

6-10

Cycles/min

50cycles

Test2

125V

3A

0.75-0.8

6-10

Cycles/min

10000

cycles

Voltage proof:Test voltage shall be applied for 

1 min(50~60Hz, Cut-off current:0.5mA)

 3GPA125/250VAC

 Operation Cycles:10,000 次 ;

Operation Frequency:15~20 /min

Voltage proof:Test voltage shall be applied for

 1 min(50~60Hz, Cut-off current:0.5mA)

 

 

Insulation 

resistance

(item 4.2):

50MΩ MIN

Voltage proof:

Terminal and 

terminal:1000VAC

No dielectric 

breakdown shall 

occur.

 

Operating 

characteristic 

(item 5.1):

Within 20% 

of specified
value .

 

6000 cycles 

temperature 

rise: 30℃ MAX

10000cycles 

temperature 

rise: 55℃ MAX

No abnormalities 

shall be 

recognized in 

appearance and 

construction.

 

1.7.2

 

Endurance

(According to 

EN61058-1

/IEC61058-1)

3(0.5)A250VAC 

Operating Cycles:10,000 cycles 

Operation Frequency:15~20 cycles/m 3(0.5)A 250VAC 

Voltage proof:Test voltage shall be applied for 

1 min(50~60Hz, Cut-off current:0.5mA)

 

 

Insulation 

resistance

(item 4.2): 

50MΩ MIN

Voltage proof:

Terminal and 

terminal:750VAC

Terminal and 

ground:1500VAC

No dielectric 

breakdown 

shall occur.

Operating 

characteristic 

(item 5.1):

Within ±20% 

of specified
value .

Temperature 

rise:55℃ MAX

No abnormalities 

shall be 

recognized in 

appearance 

and construction

2. DRAWING & DIMENSION

3. CIRCUIT DIAGRAM

4.1

 Packing material:

Plastic box / 
Double-layers paper carton

4.2

 Packing number:

100 pieces per box 
4 inner cartons per shipping carton
Each shipping carton 10000 pieces

4.3

Weight:

Gross Weight:  8.5kg

 Net Weight:  7.0kg

4.4

 Size:

31.0 x 25.0 x 34.5 CM / 0.045CBM

Approved Rating

Mark

Reference No.

3(0.5)A125/250VAC3GPA125/250VAC3RA125/250VAC40T85,1E4,50-60HzIP403 A, 30 V dc40T85,1E4, IP40

UL&CUL

E176213

 

VDE

 

3(0.5)A250VAC

CQC

CQC07002020246

 

NEMKO

 

 

SEMKO

 

 

FIMKO

 

3(0.5) A, 125/250 VAC3 RA, 125/250 VAC3 A, 

30 V d.c.40T85, 1E4, 50-60Hz, IP40

DEMKO

D-00719

3(0.5)A250VAC

CE

AN501823730001

3(0.5)A250VAC

TUV

R50060067

3(0.5) A, 125/250 VAC3 RA, 125/250 VAC3 A, 30 

V d.c.40T85, 1E4, 50-60Hz,    IP40

 

ENEC

ENEC-00182

3(0.5)A250VAC  10E3 T85

EK

SU02030-8001A

3(0.5) A, 125/250 VAC3 RA, 125/250 VAC3 A, 30 V 

d.c.40T85, 1E4, 50-60Hz, IP40

 

CB

DK-5190

 

PARTS LIST

NO.

QUANTITY

Item

Material

1

1

plunger

Engineering plastic White PBT

2

1

cover

Engineering plastic Black PBT

3

1

Moving piece

Beryllium alloy QBe2

4

1

support

Brass alloy H65,Silver plated

5

1

case

Engineering plastic White PBT

6

1

NO terminal

Brass alloy H65,Silver plated

7

1

contact

AgNi10, Gold plated

8

1

NC terminal

AgNi10/Cu

9 1

contact

AgNi10, Gold plated

10 1

Moving arm

Stainless steel SUS304

Note: Returned plastic should not exceed 20%.

return