Home » Products » Push Button Switch » Waterproof Push Button Switch

KAN-L6-WP waterproof IP67 locked push button switch with LED 16A 250VAC

Series:KAN-L6 series

Description:

Configuration:                           Single-Pole Single-Through (SPST-NO)
Terminal form:                          Solder Terminal
Mounting:                         Fixing on the housing of switch
Protection:                               Comply with IP67
Resistance to tracking PTI:    175V

Contact Now

Applications
Technical parameters
Remarks

Enormous remote controller and portable remote controller Instrumentation Medical equipment Telecommunications and networking equipment Computers & peripherals Instrumentation and controls Industrial electronic equipment Industrial remote controller Medical Equipment Communication Outdoor Controls Public building, Home security, Business building, Industrial equipment…etc.

3.DETAIL SPECIFICATIONS:
Type: KAN-L6-WP
Construction category:D type
Operation method:Gear shifting
Configuration:Single-Pole Single-Through (SPST-NO)
Terminal form:Solder Terminal
Mounting:Fixing on the housing of switch
Protection:Comply with IP67
Resistance to tracking PTI: 175V
3.1 OPERATING CHARACTERISTICS
3.2 General
Rating Value : 16(4)A250VAC 10E3; 12(10)A250VAC 10E3, 10(8)A250VAC 5E4,according to IEC61058-1
3.2.1 Application This specification is correspondent to KAN-L6-GB SERIES Switch used for household electronic appliance.
3.2.2 Operating Temperature Range   0℃~+105℃;
3.2.3 Test Conditions    Unless otherwise specified. The atmospheric conditions for making measurements and
tests are as follows:

Ambient temperature:5~35℃
Relative humidity:45~85%
Air pressure:8.6~10.6kPa (860~1060 mbar)
3.3Appearance construction and dimensions
3.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
3.3.2 Construction and dimensions Refer to individual product drawing.
3.4. Electronic characteristics：

NO.

Items

Test conditions

Criteria

3.4.1

Contact
resistance
Measured at low
current (100mA or less).
30mΩ MAX

3.4.2

Insulation
resistance

Measurement shall be made between
adjacent terminals, between terminal
and shell(DC 500V)

100MΩ MIN, at DC500V

3.4.3

Voltage
proof

AC 2000V, 1min.
(before endurance test)
AC 1500V, 1min.
(after endurance test)

No arcing , break- down
and damaging insulation.

3.5.  Mechanical characteristic

Characteristics

Units

Standards

Requirements

Actuating Force

N

1P:7N±1N, 2P: 10N±1N

See Drawing

Contact pressure

N

0.8N MIN

See Drawing

Push and draw force on the terminals of max.80N may not effect the functioning of the switch.

3.6.  Durability

NO.

Item

Test condition

Criteria

3.6.1

Endurance

(According to

UL61058)

16(4)A250VAC 10E3; 12(10)A250VAC
10E3, 10(8)A250VAC 5E4

Switch shall be operated according
to following sequence

(Test1~Test2)

Voltage

Current

Power
factor

Operation
rate

Number
of
operation

Test1

125V

20A

0.75-0.8

6-10

cycles/min

50cycles

Test2

125V

16A

0.75-0.8

6-10

cycles/min

6000cycles

Voltage proof(Cut-off current:0.5mA)

Switch shall be operated 50,000
cycles at 15-20 cycles/min.

Test voltages shall be applied for 1 min

Insulation resistance
(item 4.2):

100MΩ MIN

Voltage proof:

Terminal and ground:1000VAC

No dielectric breakdown
shall occur.

Operating characteristic
(item 5.1):

Operating characteristic variety

Within ±20% of specified value .

6000 cycles temperature
rise:45℃ MAX;

10,000 cycles temperature
rise:55℃ MAX;

No abnormalities shall be
recognized in appearance
and construction

3.6.2

Endurance

(According to
EN61058-1

/IEC61058-1)

16(4)A250VAC 10E3;
12(10)A250VAC 10E3,
10(8)A250VAC 5E4

Switch shall be operated
50,000 cycles at
15~20 cycles/min

Voltage proof(Cut-off
current:0.5mA)

Test voltages shall be
applied for 1 min.

Insulation resistance(item 4.2):

100MΩ MIN

Voltage proof:

Terminal and terminal:750VAC

Terminal and ground:1500VAC

No dielectric breakdown shall occur.

Operating characteristic (item 5.1):

Operating characteristic variety

Within ±20% of specified value .

Temperature rise:55℃ MAX

No abnormalities shall be
recognized in appearance
and construction

4. Test Sequence:

1

Operating Life

5000 cycles at 105°C,5000 cycles
at room temperature at 16(4)A 250VAC,
12(10)A250VAC

Or

25000 cycles at 105°C,25000
cycles at room temperature at

10(8)250VAC

Life test:100.000cycles After
test: Contact resistance: 30m
ΩMax Insulation resistance: 100MΩ
Min Operating force:  Change should be
within  ±50% of specified value.
No abnormalities shall  be recognized
in  appearance and  construction

2

PCB
Soldering Version

Solder ability and Resistance to sold heat
according to IEC 68-2-20

Appearance should be not
damaged,electrical and
mechanical characteristics
shall be satisfied.

3

Solder ability Tes

The top of the terminals shall be dipped in
the solder bath at  230±5℃ for 5±1 seconds.

Ninety-five percent of terminals
shall be dipped.

4

Resistance
to Heat Tes

The switch shall be stored at a temperature
of 80±2℃ for 96 hours, Measurements shall be made
after it be subjected to the standard conditions for 1 hour.

Appearance,construction and item

Contact resistance: 30mΩ Max

Insulation resistance:100MΩMin

5

The SaltTesting

The switch shall be checked after following
test: 1.Temperature: 35±5ºC 2.Salt solution:
5±1%(Solids by mass)  3.Duration: 24 hours,
4.After immersing, salt deposit shall be removed by
running water.

The testing standard based on
bubble, crack, and magnifying
glass with gauge.

6

Resistance
to Cold Test

The switch shall be stored at a temperature
of -25±3℃ for 96 hours, Measurements shall be made
after it be subjected to the standard conditions for 1 hour.

Appearance,construction and item

Contact resistance: 30mΩ Max

Insulation resistance:100MΩMin

7

Resistance
to Humidity Test

The switch shall be stored at a temperature
of 40±2℃,relative humidity 90~96% for 96 hours,
Measurements shall be made after it be subjected to the
standard conditions for 1 hour (Wipe out water drip)

Appearance,construction and item

Contact resistance: 30mΩ Max

Insulation resistance:100MΩMin

5. Precautions in Handling
Care should be exercised so that flux from the upper part of the printed circuit
board does not adhere to the switch.
6. DRAWING & DIMENSION:

7.CIRCUIT DIAGRAM：

9. PACKING:

9.1

Packing material:

Plastic box /

Five -layers paper carton

9.2

Packing number:

200pcs/bag, 1bags in  a box  , 10 boxes /big cargo,
2,000 PCS / big cargo

9.3

Weight:

Gross Weight:  5.35 kg

Net Weight:    5.05 kg

9.4

Size:

57x26x32      cm

Approved Rating	Mark	Reference No.
16(4)A250VAC 10E3;	UL&CUL	UL1054
10(8)A250VAC 5E4	TUV
12(10)A250VAC 10E3,	CQC	IEC61058

NO.	quantity	Items	Material
1	1	Case Housing	Nylon PA66
2	1	Actuator	PA66
3	1	Cover	Nylon PA66 or PC
4	1	Spring	STEEL WIRE
5	1	Terminal and Lever	Copper Alloy
RoHS: 2002/95/ EC

Language

KAN-L6-WP waterproof IP67 locked push button switch with LED 16A 250VAC

3.5. Mechanical characteristic

3.6. Durability

4. Test Sequence:

Products list

Micro Switch

Rocker Switch

Tactile Switch

Push Button Switch

Slide Switch

Toggle Switch

Dip Switch

Socket

pressure switch

NO.	Items	Test conditions	Criteria
3.4.1	Contact resistance	Measured at low current (100mA or less).	30mΩ MAX
3.4.2	Insulation resistance	Measurement shall be made between adjacent terminals, between terminal and shell(DC 500V)	100MΩ MIN, at DC500V
3.4.3	Voltage proof	AC 2000V, 1min. (before endurance test) AC 1500V, 1min. (after endurance test)	No arcing , break- down and damaging insulation.

Characteristics	Units	Standards	Requirements
Actuating Force	N	1P:7N±1N, 2P: 10N±1N	See Drawing
Contact pressure	N	0.8N MIN	See Drawing
Push and draw force on the terminals of max.80N may not effect the functioning of the switch.

1		Operating Life	5000 cycles at 105°C,5000 cycles at room temperature at 16(4)A 250VAC, 12(10)A250VAC Or 25000 cycles at 105°C,25000 cycles at room temperature at 10(8)250VAC		Life test:100.000cycles After test: Contact resistance: 30m ΩMax Insulation resistance: 100MΩ Min Operating force: Change should be within ±50% of specified value. No abnormalities shall be recognized in appearance and construction
2		PCB Soldering Version	Solder ability and Resistance to sold heat according to IEC 68-2-20		Appearance should be not damaged,electrical and mechanical characteristics shall be satisfied.
3		Solder ability Tes	The top of the terminals shall be dipped in the solder bath at 230±5℃ for 5±1 seconds.		Ninety-five percent of terminals shall be dipped.
4		Resistance to Heat Tes	The switch shall be stored at a temperature of 80±2℃ for 96 hours, Measurements shall be made after it be subjected to the standard conditions for 1 hour.		Appearance,construction and item Contact resistance: 30mΩ Max Insulation resistance:100MΩMin
5	The SaltTesting			The switch shall be checked after following test: 1.Temperature: 35±5ºC 2.Salt solution: 5±1%(Solids by mass) 3.Duration: 24 hours, 4.After immersing, salt deposit shall be removed by running water.	The testing standard based on bubble, crack, and magnifying glass with gauge.
6	Resistance to Cold Test			The switch shall be stored at a temperature of -25±3℃ for 96 hours, Measurements shall be made after it be subjected to the standard conditions for 1 hour.	Appearance,construction and item Contact resistance: 30mΩ Max Insulation resistance:100MΩMin
7	Resistance to Humidity Test			The switch shall be stored at a temperature of 40±2℃,relative humidity 90~96% for 96 hours, Measurements shall be made after it be subjected to the standard conditions for 1 hour (Wipe out water drip)	Appearance,construction and item Contact resistance: 30mΩ Max Insulation resistance:100MΩMin

9.1	Packing material:	Plastic box / Five -layers paper carton
9.2	Packing number:	200pcs/bag, 1bags in a box , 10 boxes /big cargo, 2,000 PCS / big cargo
9.3	Weight:	Gross Weight: 5.35 kg Net Weight: 5.05 kg
9.4	Size:	57x26x32 cm

Language

KAN-L6-WP waterproof IP67 locked push button switch with LED 16A 250VAC

3.5. Mechanical characteristic

3.6. Durability

4. Test Sequence:

Follow us