Language

Home » Products » Rocker Switch » Illuminated Rocker Switch

KAN-B2-25PSW28B high quality on-off 3pins SPDT round red illuminated rocker switch

Series:KAN-B2

Description:

Type:                                  KAN-B2-25PSW28B    
Construction category:   D
Operation method:         Rocker Action
Configuration:                  Single-Pole Single-Through (SPDT)
Terminal form:                  #187 quick-connect Terminal 
Mounting:                          Snap-In
Protection:                  　    IP40

Contact Now

  • Applications
  • Technical parameters
  • Remarks

Home / Household Appliances
Electric kettle, Robot cleaner, Dust catcher, Vacuum cleaner, Coffee maker, Running machine etc.

Electronic Equipment
Toys, Power tools, Car control panel etc.

1、 DETAIL SPECIFICATIONS:
Type:                                  KAN-B2-25PSW28B    
Construction category:   D
Operation method:         Rocker Action
Configuration:                  Single-Pole Single-Through (SPDT)
Terminal form:                  #187 quick-connect Terminal
Mounting:                          Snap-In
Protection:                  　    IP40

1.1    OPERATING CHARACTERISTICSNote:

Characteristics

Units

Standards

Note

Actuating Force

N

4±1.5 Max

Original 4±1.5  .

Contact Force

N

0.4 Min

Original 0.4 Min

Electrical Clearance

mm

3 Min

Original 3 Min

Actuating Force:The force required to move the actuator from the free to the operation position

1.2 GENERAL CHARACTERISTICS
1.2.1Application                              This specification is applied to KAN Rocker Switch used for electronic equipment.
1.2.2Operating temperature range       -25℃ to +105℃
1.2.3Test conditions                       Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows  
        Ambient temperature:            15~35℃
        Relative humidity:                   45~85%
        Air pressure:                            86~106kPa (860~1060 mbar)
        Should any doubt arise in judgment. tests shall be conducted at the following conditions.  
        Ambient temperature:            20±2℃
        Relative humidity:                   60~70%
        Air pressure:                            86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
1.3.1 Appearance                     Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions    Refer to individual product drawing.
3.4. Electrical specifications

NO.

Items

Test conditions

Criteria

1.4.1

Contact
resistance

Shall be measured at 12A 24VDC by voltage drop
method after some operations without load.

Applied position: Between terminal and terminal  

30mΩ MAX

1.4.2

Insulation
resistance

Test voltage:500VDC, measured after 1 min ±5s

Applied position: 1)Between terminal and terminal 

2)Between terminal and ground

100MΩ MIN

1.4.3

Voltage proof

Following test voltages shall be applied for 1 min.

(Cut-off  current:0.5mA)

1)Between terminal and terminal :
           2000VAC/min (50~60Hz)

2)Between terminal and ground:
           2500VAC/min (50~60Hz)

No dielectric breakdown

shall occur

1.5. ENVIRONMENT RESISTANCE

NO.

Item

Test conditions

Criteria

1.5.1

Cold

After testing at -25±2℃ for 96 h,
the switch shall be allowed to stand
under normal room temperature and
humidity condition for 1h, and then
measurement shall be made within 1 h.
water drops shall be removed.

Contact resistance(item 4.1): 

100mΩ MAX

Insulation resistance (item 4.2):

50MΩ MIN

Voltage proof: (item 4.3)

No dielectric
breakdown shall occur.

Operating characteristic
(item 5.1):

Operating characteristic
variety Within ±10% of
specified value .

No abnormalities shall be
recognized in appearance
and construction.

1.5.2

Dry heat

After testing at 105±2℃ for 96 h,
the switch shall be allowed to stand
under normal room temperature and
humidity condition for 1h, and then
measurement shall be made within 1 h.

1.5.3

Damp heat

After testing at 40±2℃ and 90-95%RH
for 96 h, the switch shall be allowed to
stand under normal room temperature
and humidity condition for 1h, and then
measurement shall be made within 1 h.
water drops shall be removed.

1.5.4

Change of

temperature

After 20 cycles of following conditions the
switch shall be allowed to stand under
normal room temperature and humidity
condition for 1h, and then measurement
shall be made within 1 h.
water drops shall be removed.

1.5.5

Salt mist

Switch shall be checked after following lest.

1) Temperature: 35±2℃

2) Salt solution: 5±1% (solids by mass)

3) Duration: 24±1h

After test, salt deposit shall be
removed in running water 

No remarkable corrosion shall be
recognized in metal part

1.6. WELDING CHARACTERISTICS

 

1.6.1

 

Solder ability

Switch test under such conditions and inspect after. 

1）Variable temperature range ：235±5℃；

2）Dip time：3±0.5s；

 

The area of dip tin
should capture the 95%
impregnated area

 

1.6.2

 

Resistance to
soldering heat

 

The switch will be inspect under such conditions below

Temperature and impregnated time

Trial measure

temperature（℃）

Time（s）

Slot welding method

260±5

5±1

Soldering method

350±5

3±0.5

 

 

All of the appearance,
motor functions,
electrical properties
are no abnormal.  

1.7. ENDURANCE

NO.

Item

Test condition

Criteria

1.7.1

Endurance

(According to

 UL61058)

13A 125VAC

Switch shall be operated according to following sequence

(Test1~Test2)

 

Voltage

Current

Power factor

Operation
rate

Number
of operation

Test1

125V

13.45A

0.75-0.8

6-10

cycles/min

50cycles

Test2

125V

13A

0.75-0.8

6-10

cycles/min

6000cycles

Voltage proof(Cut-off current:0.5mA)

1GPA 125/250VAC ;

Switch shall be operated 6,000 cycles at 15-20 cycles/min.

Test voltages shall be applied for 1 min

Insulation resistance(item 4.2): 

30MΩ MIN

Voltage proof:

Terminal and ground:1000VAC

No dielectric breakdown shall occur.

Operating characteristic (item 5.1):

Operating characteristic variety 

Within ±20% of specified value .

6000 cycles
temperature rise:30℃ MAX;

10,000 cycles
temperature rise:55℃ MAX;

 

No abnormalities shall
be recognized in
appearance and construction

1.7.2

Endurance

(According to
EN61058-1

/IEC61058-1)

10 (8) A 250VAC

Switch shall be operated 10,000 cycles at 15~20 cycles/min

Voltage proof(Cut-off current:0.5mA)

Test voltages shall be applied for 1 min.

Insulation resistance(item 4.2): 

50MΩ MIN

Voltage proof:

Terminal and terminal:750VAC

Terminal and ground:1500VAC

No dielectric breakdown shall occur.

Operating characteristic (item 5.1):

Operating characteristic variety 

Within ±20% of specified value .

Temperature rise:55℃ MAX

No abnormalities shall be
recognized in appearance
and construction

4. DRAWING & DIMENSION:

5. CIRCUIT DIAGRAM：

6. PACKING:

6.1

Packing material:

Plastic bag / 
Double-layers paper carton

6.2

Packing number:

100 pieces per bag 
10 bags per inner carton
2 inner cartons per shipping carton

Each shipping carton 2000 pieces

6.3

Weight:

Gross Weight:  11.75kg

Net Weight:   10.0kg 

6.4

Size:

31 x26 x27 CM /0.022CBM

SAFETY APPROVAL & RATING:

Approved Rating

Mark

Reference No.

12A24VDC  6.5A250VAC  13A125VAC

UL&CUL

E215677

 

VDE

 

10(8)A250VAC T105/55

CQC

CQC06002017321

 

NEMKO

 

 

SEMKO

 

 

FIMKO

 

 

DEMKO

 
 

CE

 

10(8)A250VAC T105/55

TUV

15013611 004

 

ENEC

 

10(8)A250VAC T105/55

EK

SU02027-12001

 

CB

 

 PARTS LIST:

ITEM

NAME

MATERIAL

1

HOUSE

NYLON

2

SHAFT

NYLON

3

BUTTON

NYLON

4

SOLDERING TERMINAL

BRASS STRIP

5

MOVING TERMINAL

BRONZE STRIP

6

SUPPORT

COPPER STRIP

7

COMPRESSED SPRING

STAINLESS STEEL WIRE

8

TOP COLUMN

BRASS STRIP

9

CONTACT

AgCdO / COPPER

10

LED

LED

Products list

About switech
Application
Contact us
Blog Rss Sitemap
<
return