
ERD30103-1B
Series:ERD30103-1B
Type: ERD30103-1B
Construction category: D
Operation method: Revolve DIP Action
Terminal form: #PCB Terminal
Mounting: Stick in
Protection: IP40
- Applications
- Technical parameters
- Remarks
-
Home / Household Appliances
Electric kettle, Robot cleaner, Dust catcher, Vacuum cleaner, Coffee maker, Running machine etc.
Electronic Equipment
Toys, Power tools, Car control panel etc.
Medical Equipment
Communication Equipment
Automation Equipment
Automotive Electronics
Instrumentation
1. DETAIL SPECIFICATIONS:
Type: ERD30103-1B
Construction category: D
Operation method: Revolve DIP Action
Terminal form: #PCB Terminal
Mounting: Stick in
Protection: IP40
Note:
Actuating Force:The force required to move the actuator from the free to the operation position
1.1GENERAL CHARACTERISTICS
1.1.1Application This specification is applied to RT-S06A Rocker Switch used for electronic equipment.
1.1.2 Operating temperature range 0℃ to 85℃
1.1.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature: 15~35℃
Relative humidity: 45~85%
Air pressure: 86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature: 20±2℃
Relative humidity: 60~70%
Air pressure: 86~106kPa (860~1060 mbar)
1.2 Appearance construction and dimensions
1.2.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.2.2 Construction and dimensions Refer to individual product drawing.
1.3. Electrical specificationsNO.
Items
Test conditions
Criteria
1.3.1
Contact resistance
Shall be measured at 1KHz SMALL CURRENT(25 mA OR LESS) by voltage drop method after some operations without load.
Applied position: Between terminal and terminal
100mΩ MAX
1.3.2
Insulation resistance
Test voltage: 100VDC, measured after 60 ±5s
Applied position:
1)Between terminal and terminal
2)Between terminal and ground
100MΩ MIN
1.4. ENVIRONMENT RESISTANCE
NO.
Item
Test conditions
Criteria
1.4.1
Cold
After testing at -25±2℃ for 96 h,
the switch shall be allowed to stand
under normal room temperature and
humidity condition for 1h, and then
measurement shall be made within 1 h.
water drops shall be removed.Contact resistance(item 4.1):
100mΩ MAX
Insulation resistance (item 4.2):
100MΩ MIN
Voltage proof: (item 4.3)
No dielectric breakdown shall occur.
Operating characteristic (item 5.1):
Operating characteristic variety
Within ±10% of specified value .No abnormalities shall be recognized
in appearance and construction.1.4.2
Dry heat
After testing at 85±2℃ for 96 h,
the switch shall be allowed to stand
under normal room temperature and
humidity condition for 1h, and then
measurement shall be made within 1 h.1.4.3
Damp heat
After testing at 40±2℃ and 90-95%RH
for 96 h, the switch shall be allowed to
stand under normal room temperature
and humidity condition for 1h, and then
measurement shall be made within 1 h.
water drops shall be removed.1.4.4
Change of
temperature
After 20 cycles of following conditions
the switch shall be allowed to stand
under normal room temperature and
humidity condition for 1h, and then
measurement shall be made within 1 h.
water drops shall be removed.1.4.5
Salt mist
Switch shall be checked after following lest.
1) Temperature: 35±2℃
2) Salt solution: 5±1% (solids by mass)
3) Duration: 24±1h
After test, salt deposit
shall be removed in running waterNo remarkable corrosion
shall be recognized in metal part
1.5. WELDING CHARACTERISTICS1.5.1
Solder ability
Switch test under such conditions and inspect after.
1)Variable temperature range :235±5℃;
2)Dip time:3±0.5s;
The area of dip tin
should capture the
95% impregnated area1.5.2
Resistance to
soldering heatThe switch will be inspect under such conditions below
Temperature and impregnated time
Trial measure
temperature(℃)
Time(s)
Slot welding method
260±5
5±1
Soldering method
350±5
3±0.5
All of the appearance,
motor functions, electrical
properties are no abnormal.
1.6. ENDURANCENO.
Item
Test condition
Criteria
1.6.1
Life Test
An actuator shall be with a thrust of no great than 1 times switch power to 3,000 cycles.
At a speed of 30 cycles for 1 minutes.
1) Contact resistance(item 4.1):
100mΩ MAX
2) Life time:
3) 3,000 cycles
1.6.2
Stem Strength
And along the running direcition at apex handle (500g) on the strength test, time is 30 seconds.
cognized in appearance
and construction
2. DRAWING & DIMENSION:3.PACKING:
3.1
Packing material:
Plastic bag /
Double-layers paper carton3.2
Packing number:
200 pieces per bag
8 bags per shipping carton
Each shipping carton 1600 pieces3.3
Weight:
Gross Weight: 8 kg
Net Weight: 7 kg
3.4
Size:
40*30*23CM /0.0276㎡
PARTS LIST:
NO.
NAME:
MATERIAL
1
Base
PBT engineering plastic
2
Cover
PBT engineering plastic
3
Push Stem
PBT engineering plastic
4
Terminal
Alloy copper –Gold plated
Returned plastic should not exceed 20%。