R13-51SW1 SPST on-off 2pins black oval rocker switch for indicator button
Series:R13
Type: R13-51SW1
Construction category: D
Operation method: Rocker Action
Configuration: Single-Pole Single-Through (SPST)
Terminal form: #187 quick-connect Terminal
Mounting: Snap-In
Protection: IP40
- Applications
- Technical parameters
- Remarks
-
Home / Household Appliances
Electric kettle, Robot cleaner, Dust catcher, Vacuum cleaner, Coffee maker, Running machine etc.
Electronic Equipment
Toys, Power tools, Car control panel etc.
Medical Equipment
Communication Equipment
Automation Equipment
Automotive Electronics
Instrumentation
1.DETAIL SPECIFICATIONS:
Type:R13-51SW1
Construction category:D
Operation method:Rocker Action
Configuration:Single-Pole Single-Through (SPST)
Terminal form:#187 quick-connect Terminal
Mounting:Snap-In
Protection:IP40
1.1OPERATING CHARACTERISTICSCharacteristics
Units
Standards
Note
Actuating Force
N
4±2 Max
Original 4±2
Contact Force
N
0.4 Min
Original 0.4 Min
Electrical Clearance
mm
3 Min
Original 3 Min
Note:
Actuating Force:The force required to move the actuator from the free to the operation position
1.2 GENERAL CHARACTERISTICS
1.2.1Application This specification is applied to R13-31 Rocker Switch used for electronic equipment.
1.2.2 Operating temperature range 0~85℃
1.2.3Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure:86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions Refer to individual product drawing.
1.4.Electrical specificationsNO.
Items
Test conditions
Criteria
1.4.1
Contact
resistance
Shall be measured
at 50VAC by voltage
drop method after
some operations
without load.
Applied position:
Between terminal
and terminal
20mΩ MAX
1.4.2
Insulation
resistance
Test voltage:500VDC,
measured after 1 min
±5s
Applied position: 1)
Between terminal and
terminal
2)Between terminal
and ground
100MΩ MIN
1.4.3
Voltage
proof
Following test voltages
shall be applied for 1 min.
(Cut-off current:0.5mA)
1)Between terminal and
terminal :1250VAC/min
(50~60Hz)
No dielectric
breakdown
shall occur
1.5. ENVIRONMENT RESISTANCE
NO.
Item
Test conditions
Criteria
1.5.1
Cold
After testing at -25±2℃
for 96 h, the switch shall
be allowed to stand under
normal room temperature
and humidity condition for
1h, and then measurement
shall be made within 1 h.
water drops shall be
removed.
Contact
resistance
(item 4.1):
100mΩ MAX
Insulation
resistance
(item 4.2):
50MΩ MIN
Voltage proof:
(item 4.3)
No dielectric
breakdown
shall occur.
Operating
characteristic
(item 5.1):
Operating
characteristic
variety Within
±10% of
specified value .
No abnormalities
shall be
recognized in
appearance and
construction.
1.5.2
Dry heat
After testing at 105±2℃ for
96 h, the switch shall be
allowed to stand under normal
room temperature and humidity
condition for 1h, and then
measurement shall be made
within 1 h.
1.5.3
Damp heat
After testing at 40±2℃ and
90-95%RH for 96 h, the switch
shall be allowed to stand under
normal room temperature and
humidity condition for 1h, and
then measurement shall be
made within 1 h. water drops
shall be removed.
1.5.4
Change of
temperature
After 20 cycles of following
conditions the switch shall
be allowed to stand under
normal room temperature
and humidity condition for
1h, and then measurement
shall be made within 1 h.
water drops shall be removed.
1.5.5
Salt mist
Switch shall be checked after
following lest.
1) Temperature: 35±2℃
2) Salt solution: 5±1%
(solids by mass)
3) Duration: 24±1h
After test, salt deposit shall
be removed in running water
No remarkable
corrosion shall
be recognized
in metal part
1.6. WELDING CHARACTERISTICS
1.6.1
Solder ability
Switch test under such conditions
and inspect after.
1）Variable temperature range ：235±5℃；
2）Dip time：3±0.5s；
The area of dip tin
should capture the
95% impregnated
area
1.6.2
Resistance to
soldering heat
The switch will be inspect under such
conditions below
Temperature and impregnated time
Trial measure
temperature
（℃）
Time
（s）
Slot welding method
260±5
5±1
Soldering method
350±5
3±0.5
All of the appearance,
motor functions,
electrical properties
are no abnormal.
1.7. ENDURANCE
NO.
Item
Test condition
Criteria
1.7.1
Endurance
(According to
UL61058)
12A 125VAC
Switch shall be operated according to following sequence
(Test1~Test2)
Voltage
Current
Power
factor
Operation
rate
Number of
operation
Test1
125V
13A
0.75-0.8
6-10
cycles/min
50cycles
Test2
125V
12A
0.75-0.8
6-10
cycles/min
6000cycles
Voltage proof(Cut-off current:0.5mA)
1GPA 125/250VAC ;
Switch shall be operated 6,000 cycles at 15-20 cycles/min.
Test voltages shall be applied for 1 min
Insulation
resistance
(item 4.2):
30MΩ MIN
Voltage
proof:
Terminal
and ground:
1000VAC
No dielectric
breakdown
shall occur.
Operating
characteristic
(item 5.1):
Operating
characteristic
variety
Within ±20%
of specified
value .
6000 cycles
temperature
rise:30℃ MAX;
10,000 cycles
temperature
rise:55℃ MAX;
No abnormalities
shall be
recognized in
appearance and
construction
1.7.2
Endurance
(According
to EN61058-1
/IEC61058-1)
12(8)A 250VAC
Switch shall be operated 10,000 cycles at 15~20 cycles/min
Voltage proof(Cut-off current:0.5mA)
Test voltages shall be applied for 1 min.
Insulation
resistance
(item 4.2):
50MΩ MIN
Voltage proof:
Terminal and
terminal:750VAC
Terminal and
ground:1500VAC
No dielectric
breakdown
shall occur.
Operating
characteristic
(item 5.1):
Operating
characteristic
variety
Within ±20%
of specified
value .
Temperature
rise:55℃ MAX
No abnormalities
shall be
recognized in
appearance and
construction
2. DRAWING & DIMENSION:
3. CIRCUIT DIAGRAM：
4. PACKING:
4.1
Packing material:
Plastic bag /
Double-layers paper carton4.2
Packing number:
200 pieces per bag
10 bags per inner carton
3 inner cartons per shipping carton1 shipping carton 6000 pieces
4.3
Weight:
Gross Weight: 26 kg
Net Weight: 24.5 kg
4.4
Size:
57*27*32CM /0.049248CBM
SAFETY APPROVAL & RATING:
Approved Rating
Mark
Reference No.
10(6)A 125/250VAC
UL&CUL
E256173
12(8)A 250VAC
VDE
0630-1
12(8)A 250VAC
CQC
CQC09002039559
NEMKO
SEMKO
FIMKO
DEMKO
CE
TUV
ENEC
EK
CB
PARTS LIST:
ITEM
NAME
MATERIAL
1
Button
Plastic
2
Base
Plastic
3
Terminal
Brass alloy H65,Silver Plated
4
Plate moving
Brass alloy H65,Silver Plated
5
Contact
Silver-Cadmium Oxide alloy
6
Contact
Silver-Cadmium Oxide alloy
7
Spring
Manganese Steel
8
Steel Ball
Stainless Steel
Returned plastic should not exceed 20%.
Skype
QQ