R13-511 gray SPST on-off 2pins black oval rocker switch for indicator button

Series:R13-51SW1 gr

Description:

Type:                                R13-511 gray
Construction category:    D
Operation method:           Rocker Action
Configuration:                   Single-Pole Single-Through (SPST)
Terminal form:                  #187 quick-connect Terminal
Mounting:                          Snap-In
Protection:                         IP40

Contact Now

  • Applications
  • Technical parameters
  • Remarks

Home / Household Appliances
Electric kettle, Robot cleaner, Dust catcher, Vacuum cleaner, Coffee maker, Running machine etc.
Electronic Equipment
Toys, Power tools, Car control panel etc.
Medical Equipment
Communication Equipment
Automation Equipment
Automotive Electronics
Instrumentation

1.DETAIL SPECIFICATIONS:
Type:R13-511 gray   
Construction category:D
Operation method:Rocker Action
Configuration:Single-Pole Single-Through (SPST)
Terminal form:#187 quick-connect Terminal
Mounting:Snap-In
Protection:IP40
1.1OPERATING CHARACTERISTICS

Characteristics

Units

Standards

Note

Actuating Force

N

4±2 Max

Original 4±2

Contact Force

N

0.4 Min

Original 0.4 Min

Electrical Clearance

mm

3 Min

Original 3 Min

Note:
Actuating Force:The force required to move the actuator from the free to the operation position
1.2 GENERAL CHARACTERISTICS
1.2.1Application This specification is applied to R13-511 Rocker Switch used for electronic equipment.
1.2.2 Operating temperature range  0~85℃
1.2.3Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows  
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.  
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure:86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions Refer to individual product drawing.
1.4.Electrical specifications

NO.

Items

Test conditions

Criteria

1.4.1

Contact 

resistance

Shall be measured 

at 50VAC by voltage 

drop method after 

some operations 

without load.

Applied position: 

Between terminal 

and terminal  

20mΩ MAX

1.4.2

Insulation 

resistance

Test voltage:500VDC, 

measured after 1 min 

±5s

Applied position: 1)

Between terminal and 

terminal 

2)Between terminal 

and ground

100MΩ MIN

1.4.3

Voltage 

proof

Following test voltages 

shall be applied for 1 min.

(Cut-off  current:0.5mA)

1)Between terminal and 

terminal :1250VAC/min 

(50~60Hz)

 

No dielectric 

breakdown

shall occur

1.5. ENVIRONMENT RESISTANCE

NO.

Item

Test conditions

Criteria

1.5.1

Cold

After testing at -25±2℃ 

for 96 h, the switch shall 

be allowed to stand under 

normal room temperature 

and humidity condition for 

1h, and then measurement 

shall be made within 1 h. 

water drops shall be 

removed.

Contact 

resistance

(item 4.1): 

100mΩ MAX

Insulation 

resistance 

(item 4.2):

50MΩ MIN

Voltage proof: 

(item 4.3)

No dielectric 

breakdown 

shall occur.

Operating 

characteristic 

(item 5.1):

Operating 

characteristic 

variety Within 

±10% of 

specified value .

No abnormalities 

shall be 

recognized in 

appearance and 

construction.

1.5.2

Dry heat

After testing at 105±2℃ for 

96 h, the switch shall be 

allowed to stand under normal 

room temperature and humidity 

condition for 1h, and then 

measurement shall be made 

within 1 h.

1.5.3

Damp heat

After testing at 40±2℃ and 

90-95%RH for 96 h, the switch 

shall be allowed to stand under 

normal room temperature and 

humidity condition for 1h, and 

then measurement shall be 

made within 1 h. water drops 

shall be removed.

1.5.4

Change of

temperature

After 20 cycles of following 

conditions the switch shall 

be allowed to stand under 

normal room temperature 

and humidity condition for 

1h, and then measurement 

shall be made within 1 h. 

water drops shall be removed.

1.5.5

Salt mist

Switch shall be checked after 

following lest.

1) Temperature: 35±2℃

2) Salt solution: 5±1% 

(solids by mass)

3) Duration: 24±1h

After test, salt deposit shall 

be removed in running water 

No remarkable 

corrosion shall 

be recognized 

in metal part

1.6. WELDING CHARACTERISTICS

 

1.6.1

 

Solder ability

Switch test under such conditions 

and inspect after. 

1Variable temperature range :235±5℃

2Dip time:3±0.5s

 

The area of dip tin 

should capture the 

95% impregnated 

area

 

1.6.2

 

Resistance to 

soldering heat

 

The switch will be inspect under such 

conditions below

Temperature and impregnated time

Trial measure

temperature

Time

s

Slot welding method

260±5

5±1

Soldering method

350±5

3±0.5

 

 

All of the appearance, 

motor functions, 

electrical properties 

are no abnormal.  

1.7. ENDURANCE

NO.

Item

Test condition

Criteria

1.7.1

Endurance

(According to

 UL61058)

12A 125VAC

Switch shall be operated according to following sequence

(Test1~Test2)

 

Voltage

Current

Power 

factor

Operation 

rate

Number of 

operation

Test1

125V

13A

0.75-0.8

6-10

cycles/min

50cycles

Test2

125V

12A

0.75-0.8

6-10

cycles/min

6000cycles

Voltage proof(Cut-off current:0.5mA)

1GPA 125/250VAC ;

Switch shall be operated 6,000 cycles at 15-20 cycles/min.

Test voltages shall be applied for 1 min

Insulation 

resistance

(item 4.2): 

30MΩ MIN

Voltage 

proof:

Terminal 

and ground:

1000VAC

No dielectric 

breakdown 

shall occur.

Operating 

characteristic 

(item 5.1):

Operating 

characteristic 

variety 

Within ±20% 

of specified 

value .

6000 cycles 

temperature 

rise:30℃ MAX;

10,000 cycles 

temperature 

rise:55℃ MAX;

 

No abnormalities 

shall be 

recognized in 

appearance and 

construction

1.7.2

Endurance

(According 

to EN61058-1

/IEC61058-1)

12(8)A 250VAC

Switch shall be operated 10,000 cycles at 15~20 cycles/min

Voltage proof(Cut-off current:0.5mA)

Test voltages shall be applied for 1 min.

Insulation 

resistance

(item 4.2): 

50MΩ MIN

Voltage proof:

Terminal and 

terminal:750VAC

Terminal and 

ground:1500VAC

No dielectric 

breakdown 

shall occur.

Operating 

characteristic 

(item 5.1):

Operating 

characteristic 

variety 

Within ±20% 

of specified 

value .

Temperature 

rise:55℃ MAX

No abnormalities 

shall be 

recognized in 

appearance and 

construction

2. DRAWING & DIMENSION:

3. CIRCUIT DIAGRAM:

4. PACKING:

4.1

Packing material:

Plastic bag / 
Double-layers paper carton

4.2

Packing number:

200 pieces per bag 
10 bags per inner carton
3 inner cartons per shipping carton 

1 shipping carton 6000 pieces

4.3

Weight:

Gross Weight: 26 kg

Net Weight: 24.5 kg

4.4

Size:

57*27*32CM /0.049248CBM

SAFETY APPROVAL & RATING:

Approved Rating

Mark

Reference No.

10(6)A 125/250VAC

UL&CUL

E256173

 

VDE

 

12(8)A 250VAC

CQC

CQC09002039559

 

NEMKO

 

 

SEMKO

 

 

FIMKO

 

 

DEMKO

 

 

CE

 

 

TUV

 

 

ENEC

 

 

EK

 

 

CB

 


 

PARTS LIST:

ITEM

NAME

MATERIAL

1

Button

Plastic

2

Base

Plastic

3

Terminal

Brass alloy H65,Silver Plated

4

Plate moving

Brass alloy H65,Silver Plated

5

Contact

Silver-Cadmium Oxide alloy

6

Contact

Silver-Cadmium Oxide alloy

7

Spring

Manganese Steel

8

Steel Ball

Stainless Steel

Returned plastic should not exceed 20%.

return