PS-585 50VDC momentary push button switch Welding in PCB board, Double-Pole Double-Through (DPDT) switch

Series:PS-585 series

Description:

Type:                          PS 585
Construction category: D type
Operation method:       Gear shifting
Configuration:              Single-PoleDouble-Through (SPDT)
Terminal form:              Solder Terminal
Mounting:                    Welding in PCB board
Protection:                  Comply with IP40

Contact Now

  • Applications
  • Technical parameters
  • Remarks

Widely used in home appliance, electronic equipment, automatic machine, communication equipment, car electron, apparatus and instrument, electric motion tool etc.
Rice cooker
Slow cooker
Electric Heating Faucet
Shredder
Computer mouse
Electromagnetic lock
Baby chair
CNC machine tools
Power generator
Test equipment
Elevator
Power tools
Air conditioner
Water heater control panel
Bathroom products
Vacuum cleaner
Kitchen products
Gas valve
Range hood machine
Microwave oven
Pass-through machine


3.DETAIL SPECIFICATIONS:
Type:PS 585
Construction category:D type
Operation method:Gear shifting
Configuration:Single-PoleDouble-Through (SPDT)
Terminal form:Solder Terminal
Mounting:Welding in PCB board
Protection:Comply with IP40
3.1 OPERATING CHARACTERISTICS
3.2 General
Rating Value:DC30V 0.1A  DC 2V 10μA(min.)
3.2.1 Application This specification is applied to PS 585witch used for electronic instrument panel.
3.2.2 Operating Temperature Range -10 ℃~+70℃;  Store Temperature Range: -20℃~80℃
3.2.3 Test Conditions   Unless otherwise specified. The atmosphere icconditions for making measurements and
tests are as follows:
Ambient temperature:5~35℃
Relative humidity:45~85%
Air pressure:8.6~10.6kPa (860~1060 mbar)
3.3Appearance construction and dimensions
3.3.1 AppearanceSwitch shall have good finishing, and no rust crack or plating failures.
3.3.2Construction and dimensionsRefer to individual product drawing.

3.4. Electronic characteristics:

NO.

Items

Test conditions

Criteria

3.4.1

Contact resistance

Measured at low current (100mA or less).

100mΩ MAX

3.4.2

Insulation resistance

 

Measurement shall be made
between adjacent terminals,
between terminal and shell(DC 500V)

100MΩ MIN

3.4.3

Voltage proof

 Apply certain voltage (50-60Hz, 
AC 250V) for 1 minute between
adjacent contacts of the connector
with 2mA leakage sensitivity.

 

No arcing , break- down
and damaging insulation.

 

3.5.Mechanical characteristic

Characteristics

Units

Standards

Requirements

Operation
Force

N

 Operate the key stoke of the switch vertically,
and then increase press strength gradually,
Measured maximum operation force while the
travel of the switch is full.

See Drawing

 

Full travel

mm

.Operate the key stoke of the switch vertically,
the travel distance of key stoke moving from
its free position to maximum moving distance
shall be measurement.

See Drawing

 Static
Strength

 

Placing the switch such that the direction of
switch operation is vertical, a static load of 
3kgf shall be applied in the direction of stem
operation for a period of 60 seconds.

There shall be no
sign of damage
mechanically
and electrically.

 

4.Test Sequence:

1

 

Operating Life

DC12V 50mA. The switch would be operated continuously by auto machine at maximum rate of 60 cycles per hours on condition that the voltage is 12V and the current is 50mA

 

Life test:100.000cycles After test: Contact resistance: 500mΩMax Insulation resistance: 10MΩ Min Operating force:  Change should be within  ±50% of specified value. No abnormalities shall  be recognized in  appearance and  construction

2

Resistance to soldering heat

 Terminals shall be dipped in the solder bath at 260±5℃ for 5± 1 seconds without additional force for

Appearance should be not damaged, electrical and mechanical characteristics shall be satisfied.

3

 Solder ability Tes

 

The top of the terminals shall be dipped in the solder bath at  230±5℃ for 5±1 seconds.

Ninety-five percent of terminals shall be dipped.

4

 Resistance to Heat Tes

The switch shall be stored at a temperature of 80±2℃ for 96 hours, Measurements shall be made after it be subjected to the standard conditions for 1 hour.

Appearance, construction and item  

Contact resistance: 200mΩ Max

Insulation resistance:50MΩMin

5

The Salt

Testing

The switch shall be checked after following test: 1.Temperature: 35±5ºC 2.Salt solution: 5±1%(Solids by mass)  3.Duration: 24 hours, 4.After immersing, salt deposit shall be removed by running water.

 

 

 

 

 

 

The testing standard based on bubble, crack, and magnifying glass with gauge.

6

 Resistance to Cold Test

The switch shall be stored at a temperature of -25±3℃ for 96 hours, Measurements shall be made after it be subjected to the standard conditions for 1 hour.

Appearance, construction and item  

Contact resistance: 200mΩ Max

Insulation resistance:50MΩMin

7

 Resistance to Humidity Test

The switch shall be stored at a temperature of 40±2℃,relative humidity 90~96% for 96 hours, Measurements shall be made after it be subjected to the standard conditions for 1 hour (Wipe out water drip)

Appearance, construction and item

Contact resistance: 200mΩ Max

Insulation resistance:50MΩMin


5. Precautions in Handling
Care should be exercised so that flux from the upper part of the printed circuit
board does not adhere to the switch.

6.DRAWING & DIMENSION:





7.CIRCUIT DIAGRAM:



8. PACKING:

8.1

Packing material:

 Plastic box / 

Five -layers paper carton

8.2

Packing number:

500pcs/bag, 2bags in a box, 4 boxin a small cargo, 4000pcs/small cargo

3 small cargo/ big cargo, 12,000 PCS / big cargo

8.3

Weight:

 Gross Weight:  5.35kg

 Net Weight:    5.05kg

8.4

Size:

57x26x32     cm

 



2.SAFETY APPROVAL & RATING:

Approved Rating

Mark

Reference No.

 

UL&CUL

 

 

VDE

 

 

CQC

 

 

NEMKO

 

 

SEMKO

 

 

FIMKO

 

 

DEMKO

 

 

CE

 

 

TUV

 

 

ENEC

 

 

EK

 

 

CB

 


 PARTS LIST:

NO.

quantity

Items

Material

1

1

 guide core

POM

2

1

cover

POM

3

1

 spring

 steel wire

4

1

 case

Nylon

5

1

 spring sheet

 Ag

6

1

terminal

 Ag

Note: Returned plastic should not exceed 20%.

return