4MS1R102VS2QES free sample ON-OFF 3 pins round waterproof rocker switch

Series:4MS

Description:

Type:                                   4MS1R102VS2QES    
Construction category:   D
Operation method:          Rocker Action
Configuration:                  Single-Pole Single-Through (SPST)
Terminal form:                 #PCB-connect Terminal
Mounting:                          Snap-In
Protection:                        IP67

Contact Now

  • Applications
  • Technical parameters
  • Remarks

Home / Household Appliances
Electric kettle, Robot cleaner, Dust catcher, Vacuum cleaner, Coffee maker, Running machine etc.
Electronic Equipment
Toys, Power tools, Car control panel etc.
Medical Equipment
Communication Equipment
Automation Equipment
Automotive Electronics
Instrumentation

1.DETAIL SPECIFICATIONS:
Type:4MS1R102VS2QES    
Construction category:D
Operation method:Rocker Action
Configuration:Single-Pole Single-Through (SPST)
Terminal form:#187 quick-connect Terminal
Mounting:Snap-In
Protection:IP65
1.1OPERATING CHARACTERISTICS

Characteristics

Units

Standards

Note

Actuating Force

N

3.5±Max

Original 3.5±1  

Contact Force

N

0.4 Min

Original 0.4 Min

Electrical Clearance

mm

3 Min

Original 3 Min

Note:
Actuating Force:The force required to move the actuator from the free to the operation position
1.2 GENERAL CHARACTERISTICS
1.2.1Application This specification is applied to KAN Rocker Switch used for electronic equipment.
1.2.2 Operating temperature range -25℃ to +105℃
1.2.3Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows  
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. tests shall be conducted at the following conditions.  
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure:86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions Refer to individual product drawing.
1.4. Electrical specifications

NO.

Items

Test conditions

Criteria

1.4.1

Contact 

resistance

The contact resistance should be 20mΩ(Max).  

20mΩ MAX

1.4.2

Insulation 

resistance

It is measured with 500V DC 1minute should be 1000MΩ(Min).

100MΩ MIN

1.4.3

Voltage 

proof

AC 2000V,1min.(before endurance test)

 AC 1500V,1min.(after endurance test)

 

No dielectric 

breakdown

shall occur

1.5. ENVIRONMENT RESISTANCE

NO.

Item

Test conditions

Criteria

1.5.1

Cold

After testing at

 -25±2℃ for 96 h, 

the switch shall be

 allowed to stand 

under normal room

 temperature and 

humidity condition 

for 1h, and then

 measurement 

shall be made within 

1 h. water drops

 shall be removed.

Contact 

resistance

(item 4.1): 

20mΩ MAX

Insulation 

resistance

 (item 4.2):

100MΩ MIN

Voltage proof:

 (item 4.3)

No dielectric 

breakdown 

shall occur.

Operating 

characteristic 

(item 5.1):

Operating 

characteristic 

variety Within 

±10% of 

specified value .

No abnormalities 

shall be 

recognized in 

appearance and 

construction.

1.5.2

Dry heat

After testing at 

105±2℃ for 96 h, the

 switch shall be 

allowed to stand under

 normal room 

temperature and humidity 

condition for 1h, 

and then measurement

 shall be made within 1 h.

1.5.3

Damp heat

After testing at 40±2℃ 

and 90-95%RH 

for 96 h, the switch 

shall be allowed to

 stand under normal 

room temperature

 and humidity condition 

for 1h, and then

 measurement shall be 

made within 1 h.

 water drops shall 

be removed.

1.5.4

Change of

temperature

After 20 cycles of 

following conditions the

 switch shall be allowed 

to stand under 

normal room temperature 

and humidity 

condition for 1h, and then

 measurement 

shall be made within 1 h.

 water drops shall 

be removed.

1.5.5

Salt mist

Switch shall be checked 

after following lest.

1) Temperature: 35±2℃

2) Salt solution: 5±1%

 (solids by mass)

3) Duration: 24±1h

After test, salt deposit

 shall be removed in 

running water 

No remarkable 

corrosion shall 

be recognized 

in metal part

1.6. WELDING CHARACTERISTICS

 

1.6.1

 

Solder ability

Switch test under such 

conditions and inspect after. 

1)Variable temperature 

range :235±5℃;

2)Dip time:3±0.5s;

 

The area of dip tin 

should capture the 

95% impregnated 

area

 

1.6.2

 

Resistance to 

soldering heat

 

The switch will be inspect 

under such conditions below

Temperature and impregnated time

Trial measure

temperature

(℃)

Time(s)

Slot welding method

260±5

5±1

Soldering method

350±5

3±0.5

 

 

All of the appearance, 

motor functions, 

electrical properties 

are no abnormal.  

1.7. ENDURANCE

NO.

Item

Test condition

Criteria

1.7.1

Endurance

(According to

 UL61058)

3A 120VAC 1A 250VAC

Switch shall be operated according to following sequence

(Test1~Test2)

 

Voltage

Current

Power 

factor

Operation 

rate

Number of

 operation

Test1

120V

3A

0.75-0.8

6-10

cycles/min

50cycles

Test2

120V

3A

0.75-0.8

6-10

cycles/min

30000cycles

Voltage proof(Cut-off current:0.5mA)

3A 120VAC 1A 250VAC

Switch shall be operated 30,000 cycles at 15-20 cycles/min.

Test voltages shall be applied for 1 min

 

Insulation 

resistance

(item 4.2): 

100MΩ MIN

Voltage 

proof:

Terminal 

and ground:

1000VAC

No dielectric 

breakdown 

shall occur.

Operating 

characteristic 

(item 5.1):

Operating 

characteristic 

variety 

Within ±20% 

of specified 

value .

6000 cycles 

temperature 

rise:30℃ MAX;

10,000 cycles 

temperature 

rise:55℃ MAX;

 

No 

abnormalities 

shall be 

recognized 

in appearance 

and 

construction

1.7.2

Endurance

(According to 

EN61058-1

/IEC61058-1)

3A 120VAC 1A 250VAC

Switch shall be operated 30,000 cycles at 15~20 cycles/min

Voltage proof(Cut-off current:0.5mA)

Test voltages shall be applied for 1 min.

 

Insulation 

resistance

(item 4.2): 

100MΩ MIN

Voltage proof:

Terminal and 

terminal:750VAC

Terminal and 

ground:1500VAC

No dielectric 

breakdown 

shall occur.

Operating 

characteristic 

(item 5.1):

Operating 

characteristic 

variety 

Within ±20% 

of specified 

value .

Temperature 

rise:55℃ MAX

No abnormalities 

shall be 

recognized in 

appearance and 

construction

1.6. SOLDERING

Solder ability and Resistance to sold heat according to IEC 68-2-20

2. DRAWING & DIMENSION:

3. PACKING:

3.1

Packing material:

Plastic bag  
Double-layers paper carton

3.2

Packing number:

100 pieces per bag 
10 bags per inner carton
2 inner cartons per shipping carton

Each shipping carton 2000 pieces

3.3

Weight:

Gross Weight:  13.75kg

Net Weight:   12.56kg  

3.4

Size:

31 x26 x27 CM /0.022CBM

SAFETY APPROVAL & RATING:

Approved Rating

Mark

Reference No.

3A 120VAC 1A 250VAC

UL&CUL

 

 

VDE

 

 

CQC

 

 

NEMKO

 

 

SEMKO

 

 

FIMKO

 

 

DEMKO

 

 

CE

 

 

TUV

 

 

ENEC

 

 

EK

 

 

CB

 

 PARTS LIST:

ITEM

NAME

MATERIAL

1

Case

Diallyl phthalate(DAP)(UL94V-0)

2

Actuator

Nylon black std

3

Bushing

Brass nickel plated

4

Housing

Stainless steel

5

Switch support

Brass, tin plated

6

Terminals/contact

Brass, with silver or gold plated

7



Returned plastic should not exceed 20%.

return