MS10-10ZSW0-A075 Mini Snap Action Switch replace Omron/Panasonic/ Cherry

Series:MS10 series

Description:

Type:MS10-10ZSW0-A075
Construction category:D type
Operation method:Snap Action
Configuration:Single-Pole Double -Throw (SPDT)
Terminal form:#250 Quick-connect Terminal
Mounting:via side mounting holes
Protection:IP40

Contact Now

  • Applications
  • Technical parameters
  • Remarks

Widely used in home appliance, electronic equipment, automatic machine,
communication equipment, car electron, apparatus and instrument, electric motion tool etc.

Electric Heating Faucet
Shredder

Baby chair
CNC machine tools
Power generator
Test equipment

Power tools
Air conditioner
Water heater control panel
Bathroom products
Vacuum cleaner
Kitchen products

Range hood machine
Microwave oven
Pass-through machine


3.DETAIL SPECIFICATIONS
Type:MS10-10ZSW0-A075
Construction category:D type
Operation method:Snap Action
Configuration:Single-Pole Double -Throw (SPDT)
Terminal form:#250 Quick-connect Terminal
Mounting:via side mounting holes
Protection:IP40
3.1OPERATING CHARACTERISTICS

Characteristics

Units

Standards

Note

Actuating Force

N

0.75 Max

Original 0.75Max

Pretravel

mm

1.2 Max

Original 1.2 Max

Operating Position

mm

14.6 ± 0.5

Original 14.6 ± 0.5

Note:
Actuating Force:
The force required to move the actuator from the free to the operation position
Release Force
The force allowed the mechanism to reset actuator after operation
Free Position
The position of the actuator when no external force is applied
Operating Position
The position of the actuator when contact change-over take place
Movement Differential
The distance between operation and release position

3.2 General
3.2.1 Application This specification is applied to KW10 Micro Switch used for electronic equipment.
3.2.2 Operating Temperature range -25℃ ~ +105℃
3.2.3 Test condition Unless otherwise specified. The atmospheric conditions for making measurements  and tests are as follows:
Ambient temperature: 15~35℃
Relative humidity: 45~85%
Air pressure: 86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. It shall be conducted at the following conditions.
Ambient Temperature: 20±2℃
Relative humidity: 60~70%
Air pressure: 86~106kPa (860~1060 mbar)
3.3 Appearance Construction and Dimension
3.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
3.3.2construction and dimensions Refer to individual product drawing.
3.4. Electrical Specifications

NO.

Item

Test Condition

Criteria

3.4.1

Contact 

Resistance

Shall be measured at 1A,5V DC by voltage

 drop method after some operations 

without load.

Applied position: Between terminal “C” and terminal “NO”.

50mΩ MAX

3.4.2

Insulation 

Resistance

Test voltage:500VDC, measured after 1 min ±5s

Applied Position: applied position: 
1)Between terminal “C” and terminal “NO”

2)Between terminal and ground

100MΩ MIN

3.4.3

Voltage 

proof

Following test voltages shall be applied for 1 min.

1)Between terminal “C” and terminal

 “NO”:1000VAC (50~60Hz)

2)Between terminal and ground: 1500V AC(50~60Hz)

No dielectric 

breakdown shall 

occur

3.5. Durability

NO.

Item

Test Condition

Criteria

3.5.1

Cold

After testing at -25±2℃ for 96 h, 

the switch shall be allowed to stand 

under normal room temperature

 and humidity condition for 1h, and 

then measurement shall be made

 within 1 h. water drops shall be 

removed.

Contact 

resistance

(item 4.1): 

100mΩ 

MAX

Insulation 

resistance 

(item 4.2):

50MΩ MIN

Voltage 

proof: 

(item 4.3)

No dielectric 

breakdown 

shall occur.

Within 10% 

of specified
value .

No 

abnormalities 

shall be

 recognized 

in 

appearance 

and 

construction

 

3.5.2

Dry heat

After testing at 105±2℃ for 96 h,

 the switch shall be allowed to stand 

under normal room temperature 

and humidity condition for 1h, and 

then measurement shall be made 

within 1 h.

3.5.3

Damp Heat

After testing at 40±2℃ and 

90-95%RH for 96 h, the switch shall be 

allowed to stand under normal 

room temperature and humidity 

condition for 1h, and then 

measurement shall be made within 1 h. 

water drops shall be removed.

3.5.4

Change of Temperature

After 5 cycles of following conditions

 the switch shall be allowed 

to stand under normal room 

temperature and humidity condition 

for 1h, and then measurement 

shall be made within 1 h. water 

drops shall be removed.

3.6 Durability

NO.

Item

Test Condition

Criteria

 

3.6.1

 

Endurance

(According to

 UL61058)

 

1/2hp 125VAC

Switch shall be operated according to following sequence

(Test1~Test2)

 

Voltage

Current

Power

 Factor

Operation

 Rate

Operation

 Cycles

Test 1

125V

58.8 A

0.4-0.5

6-10Cycles/min

50cycles

Test2

125V

4.9 A

0.7-0.8

6-10Cycles/min

50000cycles

Voltage proof:Test voltage shall be applied for 

1 min(50~60Hz, Cut-off current:0.5mA)

 

10GPA 125/250VAC; 6A 30VDC

Operation Cycles:50,000 次 ;

Operation Frequency:15~20 /min

Voltage proof:Test voltage shall be applied for 

1 min(50~60Hz, Cut-off current:0.5mA)

 

Insulation 

resistance

(item 4.2):

50MΩ MIN

Voltage proof:

Terminal and

terminal:

1000VAC

No dielectric 

breakdown 

shall occur.

 

Operating 

characteristic 

(item 5.1):

Within 20% 

of specified
value .

 

6000 cycles 

temperature 

rise: 30℃ 

MAX

10000cycles 

temperature 

rise: 55℃ 

MAX

No 

abnormalities 

shall be 

recognized in 

appearance 

and 

construction.

 

3.6.2

 

Endurance

(According 

to EN61058-1

/IEC61058-1)

 

10(3)A 125/250VAC; 6A 30VDC

Operating Cycles:50,000 cycles 

Operation Frequency:15~20 cycles/m 3(0.5)A 250VAC 

Voltage proof:Test voltage shall be applied for 

1 min(50~60Hz, Cut-off current:0.5mA)

 

 

Insulation 

resistance

(item 4.2): 

50MΩ MIN

Voltage proof:

Terminal 

and terminal:

750VAC

Terminal 

and ground:

1125VAC

No dielectric 

breakdown 

shall occur.

Operating 

characteristic 

(item 5.1):

Within ±20% 

of specified
value .

Temperature 

rise:55℃ MAX

No 

abnormalities 

shall be

recognized 

in appearance 

and 

construction

4. DRAWING & DIMENSION

5. CIRCUIT DIAGRAM

 

7.  PACKING:

7.1

 Packing material:

Plastic box / 
Double-layers paper carton

7.2

 Packing number:

100 pieces per box 
4 inner cartons per shipping carton
Each shipping carton 10000 pieces

7.3

Weight:

Gross Weight:  8.5kg

 Net Weight:  7.0kg

7.4

 Size:

31.0 x 25.0 x 34.5 CM / 0.045CBM

SAFETY APPROVAL & RATING:

Approved Rating

Mark

Reference No.

10A 125V/250V AC 1/4hp 250V AC 1/2hp

125V AC 1E4 T125

10(3)A 125/250V AC 10GPA,125/250V AC,1/3hp 

125/250V AC, 6A 30VDC 50-60Hz 25T105 5E4

UL&CUL

E176213

 

VDE

 

10(3)A 125V/250V AC 5E4 25T105

CQC

CQC10002048742

 

NEMKO

 

 

SEMKO

 

 

FIMKO

 

10(3)A 125V/250V AC 6A 30VDC 50-60Hz 5E4 25T105 IP40

DEMKO

D-00720

 

CE

 

 

TUV

 

10(3)A 125V/250V AC 6A 30VDC 50-60Hz 5E4 25T105 IP40

ENEC

ENEC-00183

 

EK

 

10(3)A 125V/250V AC 6A 30VDC 50-60Hz 5E4 25T105 IP40

CB

DK-5193

 

6. PARTS LIST

NO.

QUANTITY

Item

Material

1

1

plunger

Engineering plastic Black  PPS-hGR40/41(UL94V-0)

2

1

cover

Engineering plastic Black PBT(UL94V—0)

3

1

Moving piece

Beryllium bronze C1720 HM QSn6.5-0.1

4

1

support

The brass strip H65 Plate with silver

5

1

case

Engineering plastic Black PBT(UL94V—0)

6

1

NC terminal

The brass strip H65 Plate with silver

7

1

contact

AgNi10, Gold plated

8

1

NO terminal

AgNi10/Cu

Note: Returned plastic should not exceed 20%.

return