MK-SW-22D10G5 -silde switch 1P2T
RATING:DC 50V 0.3A
- Technical parameters
1.Digital Products: digital camera, digital video and so on;
2.Remote Control: the remote control of automobile domestic security products;
3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ，refrigerator，washer;air-conditioning and so on;
5.Security Products: visual interphone, monitor and so on;
6.Toys: electric toys and so on;
7.Computer Products: PC camera and so on;
8.Exercises Machines: treadmills, massage armchair and so on;
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
10.Others: laser pen ，Pointer，Wireless mouse remote control pen，Laser projection pen，page turner，electronic pen；MousePen；overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders，automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.
1.1 OPERATING CHARACTERISTICS
Measurement shall be made at the nearest
Point of the component or at the point 3mm
From the tip of the actuator(KNOB)
A static load of (300gf) shall be applied characteristics shall to the terminal for 15 sec in any direction
Mechanical and electrical characteristics shall be satisfied without looseness of actuator
Displacement of actuator (KNOB)
A static load of 10N(1Kgf) shall be applied to the top the actuator(KNOB) and then
Displacement shall be measured to the direction of the arrow.
The lever shall have no serious deformation and function is normally.
1.2 GENERAL CHARACTERISTICS
1.2.1 Application This specification is applied to MK-SW-22DSilde Switch used for electronic equipment.
1.2.2 Operating temperature range -10℃ + 50℃
1.2.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature: 5~35℃
Relative humidity: 45~85%
Air pressure: 86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions Refer to individual product drawing.
1.4. Electrical specifications
Measured at 1KHz small current (100mA or less)
Apply a voltage of 500V DC for 1 MIN.
To following portions after which measurement shall be made.
(1)Between body and terminal.
(2) Between terminals.
AC 500V rms(50-60Hz) for 1 min trip
(1) Between terminals.
(2) Between individual terminal and frame.
Without damage to parts arcing or breakdown etc
1.5. Environment Resistance
After testing at 0±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.
There shall be no deformation or cracks in molded part.
After testing at 85±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h.
After testing at 40±2℃ and 90-95%RH for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.
After 5 cycles of following conditions the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed.
1.6. WELDING CHARACTERISTICS
Solder ability test
The top of the terminals shall be dipped 2mm in the solder bath of 230±5℃ for 3±0.5 seconds.
The area of soldering should be over
Resistance to soldering
Soldering iron method:
Bit temperature 350±10℃
Application time of soldering iron 3±0.5 sec however excessive pressure shall not be applied to the terminal.
Without load :
An actuator shall be subject to 10,000 cycles at a speed of 15 to 18 cycles for 1 min.
50 mΩ MIN
Withstand voltage 500VAC, AC 500V, 1 minute.AC 500V 1 Operating force±30% Initial value. Without damage to parts arcing or breakdown etc.
2. DRAWING & DIMENSION:
1. PARTS LIST:
PA6T/0.3mm BRASS STRIP
Returned plastic should not exceed 20%.
Double-layers paper carton
500 pieces per bag
1 bag per inner carton
10 inner cartons per shipping carton
Each shipping carton 5000 pieces
Gross Weight: 700g
Net Weight: 560g （500PCS）
X x X x X CM /XCBM