KW10-ZSW3P075 Hot Sale Zippy Equivalent Snap Action Switch 75gf

Series:KW10 series

Description:

Type:KW10-ZSW3P075
Construction category:D type
Operation method:Snap Action
Configuration:Single-Pole Double -Throw (SPDT)
Terminal form:PCB Terminal
Mounting:via side mounting holes
Protection:Comply with IP40

Contact Now

  • Applications
  • Technical parameters
  • Remarks

Widely used in home appliance, electronic equipment, automatic machine,
communication equipment, car electron, apparatus and instrument, electric motion tool etc.

Rice cooker
Slow cooker
Electric Heating Faucet
Shredder
Computer mouse

CNC machine tools
Power generator
Test equipment
Elevator
Power tools

1.DETAIL SPECIFICATIONS
Type:KW10-ZSW3P075
Construction category:D type
Operation method:Snap Action
Configuration:Single-Pole Double -Throw (SPDT)
Terminal form:PCB Terminal
Mounting:via side mounting holes
Protection:Comply with IP40

1.1OPERATING CHARACTERISTICS

Characteristics

Units

Standards

Note

Actuating Force

N

0.23 N Max

Original 0.23max.

Free Position

mm

9.5 Max

Original

9.5 max.

Operating Position

mm

7.0± 1.2

Original

7.0± 1.2

Note:
Actuating Force:
The force required to move the actuator from the free to the operation position
Release Force
The force allowed the mechanism to reset actuator after operation
Free Position
The position of the actuator when no external force is applied
Operating Position
The position of the actuator when contact change-over take place
Movement Differential
The distance between operation and release position

1.2 General
1.2.1 Application This specification is applied to KW10 Micro Switch used for electronic equipment.
1.2.2 Operating Temperature range -40℃ ~ +85℃
1.2.3 Test condition        Unless otherwise specified. The atmospheric conditions for making measurements And tests are as follows:
Ambient temperature: 15~35℃
Relative humidity: 45~85%
Should any doubt arise in judgment. It shall be conducted at the following conditions.
Ambient Temperature: 20±2℃
Relative humidity: 60~70%
Air pressure: 86~106kPa (860~1060 mbar)
1.3 Appearance Construction and Dimension
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2construction and dimensions Refer to individual product drawing.
1.4. Electrical Specifications

NO.

Item

Test Condition

Criteria

1.4.1

Contact Resistance

Shall be measured at 1A,5V DC by voltage 

drop method after some operations 

without load.

Applied position: Between terminal “C” and terminal “NO”.

50mΩ MAX

1.4.2

Insulation Resistance

Test voltage:500VDC, measured after 1 min ±5s

Applied Position: applied position: 
1)Between terminal “C” and terminal “NO”

2)Between terminal and ground

100MΩ MIN

1.4.3

Voltage proof

Following test voltages shall be applied for 1 min.

1)Between terminal “C” and

 terminal “NO”:600VAC (50~60Hz)

2)Between terminal and ground: 1000V AC(50~60Hz)

No dielectric 

breakdown 

shall occur

1.5. Durability

NO.

Item

Test Condition

Criteria

1.5.1

Cold

After testing at -40±2℃ for 96 h,

 the switch shall be allowed to 

stand under normal room 

temperature and humidity condition for 

1h, and then measurement 

shall be made within 1 h. water drops 

shall be removed.

Contact 

resistance

(item 4.1): 

100mΩ MAX

Insulation 

resistance

 (item 4.2):

50MΩ MIN

Voltage proof: 

(item 4.3)

No dielectric 

breakdown 

shall occur.

Within 10% of 

specified
value .

No abnormalities 

shall be 

recognized 

in appearance 

and construction

 

1.5.2

Dry heat

After testing at 85±2℃ for 96 h, 

the switch shall be allowed to stand 

under normal room temperature 

and humidity condition for 1h, and 

then measurement shall be made

 within 1 h.

1.5.3

Damp Heat

After testing at 40±2℃ and

90-95%RH for 96 h, the switch shall be 

allowed to stand under normal room 

temperature and humidity 

condition for 1h, and then 

measurement shall be made within 1 h. 

water drops shall be removed.

1.5.4

Change of 

Temperature

After 5 cycles of following conditions

 the switch shall be allowed to 

stand under normal room 

temperature and humidity condition for 

1h, and then measurement shall 

be made within 1 h. water drops 

shall be removed.

1.5.5

Salt Mist

Switch shall be checked after following lest.

1) Temperature: 35±2℃

2) Salt solution: 5±1% (solids by mass)

3) Duration: 24±1h

After test, salt deposit shall be 

removed in running water

 

No remarkable 

corrosion shall 

be recognized 

in metal part

1.6. Welding Performance

 

1.6.1

 

Solder ability

Switch test under such conditions 

and inspect after. 

1Variable temperature range :235±5℃

2Dip time:3±0.5s

 

The area of 

dip tin should 

capture 

the 95% 

impregnated 

area

 

1.6.2

 

Resistance to soldering heat

 

The switch will be inspect under such 

conditions below

        Temperature and impregnated time

Trial 

measure

temperature(

Time(s

Slot welding

 method

260±5

5±1

Soldering

 method

350±5

3±0.5

 

 

 

All of the 

appearance, 

motor

 functions, 

electrical 

properties are 

no abnormal. 

1.7.  Durability

NO.

Item

Test Condition

Criteria

 

1.7.1

 

Endurance

(According to

 UL61058)

1A 125VAC

Switch shall be operated according to following sequence

(Test1~Test2)

 

Voltage

Current

Power

 Factor

Operation

Rate

Operation

 Cycles

Test 1

125V

4.5A

0.75-0.8

6-10

Cycles/min

50cycles

Test2

125V

3A

0.75-0.8

6-10

Cycles/min

10000

cycles

Voltage proof:Test voltage shall be applied for 1 min

50~60Hz, Cut-off current:0.5mA)

 3GPA125/250VAC

 Operation Cycles:10,000 次 ;

Operation Frequency:15~20 /min

Voltage proof:Test voltage shall be applied for 1 min

50~60Hz, Cut-off current:0.5mA)

 

 

Insulation 

resistance

(item 4.2):

50MΩ MIN

Voltage proof:

Terminal and 

terminal:1000VAC

No dielectric 

breakdown 

shall occur.

 

Operating 

characteristic 

(item 5.1):

Within 20% 

of specified
value .

 

6000 cycles 

temperature 

rise: 30℃ MAX

10000cycles 

temperature 

rise: 55℃ MAX

No abnormalities 

shall be 

recognized in 

appearance and 

construction.

 

1.7.2

 

Endurance

(According 

to EN61058-1

/IEC61058-1)

3(0.5)A250VAC 

Operating Cycles:10,000 cycles 

Operation Frequency:15~20 cycles/m 3(0.5)A 250VAC 

Voltage proof:Test voltage shall be applied for 1 min

50~60Hz, Cut-off current:0.5mA)

 

 

Insulation 

resistance

(item 4.2): 

50MΩ MIN

Voltage proof:

Terminal and 

terminal:750VAC

Terminal and 

ground:1500VAC

No dielectric 

breakdown 

shall occur.

Operating 

characteristic 

(item 5.1):

Within ±20%

of specified
value .

Temperature 

rise:55℃ MAX

No abnormalities 

shall be 

recognized 

in appearance 

and construction

2. DRAWING & DIMENSION

3. CIRCUIT DIAGRAM

4.1

 Packing material:

Plastic box / 
Double-layers paper carton

4.2

 Packing number:

100 pieces per box 
4 inner cartons per shipping carton
Each shipping carton 10000 pieces

4.3

Weight:

Gross Weight:  8.5kg

 Net Weight:  7.0kg

4.4

 Size:

31.0 x 25.0 x 34.5 CM / 0.045CBM

Approved Rating

Mark

Reference No.

3(0.5)A125/250VAC3GPA125/250VAC3RA125/250VAC40T85,1E4,50-60HzIP403 A, 30 V dc40T85,1E4, IP40

UL&CUL

E176213

 

VDE

 

3(0.5)A250VAC

CQC

CQC07002020246

 

NEMKO

 

 

SEMKO

 

 

FIMKO

 

3(0.5) A, 125/250 VAC3 RA, 125/250 VAC3 A, 30 V d.c.40T85, 

1E4, 50-60Hz, IP40

DEMKO

D-00719

3(0.5)A250VAC

CE

AN501823730001

3(0.5)A250VAC

TUV

R50060067

3(0.5) A, 125/250 VAC3 RA, 125/250 VAC3 A, 30 V d.c.40T85, 

1E4, 50-60Hz,    IP40

 

ENEC

ENEC-00182

3(0.5)A250VAC  10E3 T85

EK

SU02030-8001A

3(0.5) A, 125/250 VAC3 RA, 125/250 VAC3 A, 30 V d.c.40T85, 

1E4, 50-60Hz, IP40

 

CB

DK-5190

 PARTS LIST

NO.

QUANTITY

Item

Material

1

1

plunger

Engineering plastic Black  PPS-hGR40/41(UL94V-0)

2

1

cover

Engineering plastic Black PBT(UL94V—0)

3

1

Moving piece

Beryllium bronze C1720 HM QSn6.5-0.1

4

1

support

The brass strip H65 Plate with silver

5

1

case

Engineering plastic Black PBT(UL94V—0)

6

1

NC terminal

The brass strip H65 Plate with silver

7

1

contact

AgNi10, Gold plated

8

1

NO terminal

AgNi10/Cu

Note: Returned plastic should not exceed 20%.

return