706-2-SWA3B2H2 2Ways 6 Pins Metal ON-OFF-ON Rocker Arms Toggle Switch
Rating： 10A 250VAC, 15A 125VAC,16A 250VAC,20A 125VAC
Terminal form: Solder Terminal
Mounting: Whole embedding
Protection: Comply with IP40
- Technical parameters
1.Digital Products: digital camera, digital video and so on;
2.Remote Control: the remote control of automobile domestic security products;
3.Communication Products: mobile phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ，refrigerator，washer;air-conditioning and so on;
5.Security Products: visual interphone, monitor and so on;
6.Toys: electric toys and so on;
7.Computer Products: PC camera and so on;
8.Exercises Machines: treadmills, massage armchair and so on;
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
10.Others: laser pen ，Pointer，Wireless mouse remote control pen，Laser projection pen，page turner，electronic pen；MousePen；overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders，automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.
1. DETAIL SPECIFICATIONS:
Rating： 10A 250VAC, 15A 125VAC,16A 250VAC,20A 125VAC
1.1 OPERATING CHARACTERISTICS
The test point is 3mm away from the rubber handle. After three times, the test is carried out.
In the front row of feet, any square type plus (500gf) strength test will take 15 seconds.
There are no cracks, loosening and other abnormalities in the terminals to meet the mechanical and electrical properties.
The force of 1Kgf is applied at the front of the handle, and the displacement should be fixed along the direction of the mark.
There is no serious deformation of the handle, and it can work normally.
The force required to move the actuator from the free to the operation position
1.2 GENERAL CHARACTERISTICS
1.2.1 Application: This specification is applied to 706-2 Toggle Switch used for electronic equipment.
1.2.2 Operating temperature range: 0℃ + 105℃
1.2.3 Test conditions : Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature: 15~35℃
Relative humidity: 45~85%
Air pressure: 86~106kPa (860~1060 mbar)
1.3 APPEARANCE, STRUCTURE AND DIMENSION
1.3.1 Appearance :Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions: Refer to individual product drawing.
1.4. Electrical specifications
The 2-4VDC is tested under tiny current (below 100mA), silver plated or gold plated.
Input 500V DC voltage for 1 minutes, test according to the following contact mode:
（1）Between the terminal.
（2）Between the terminal and the outer shell.
Input 1000V DC voltage for 1 minutes, test according to the following contact mode:
（1）Between the terminal and the outer shell.
No abnormality, such as insulation damage
Measurement under the following test:
（1） 15A 125VAC Resistive load - Plate with silver
10A 250VAC Resistive load - Plate with silver
（2）Operating frequency：The frequency of 6-8 times per minute
（3）Electrical life 6,000 make-and-break cycles.
（4）Mechanical life 10,000 make-and-break cycles.
(1) contact resistance：20 mΩ MAX
(2) insulation resistance： 1000 MΩ MIN
(3) Insulation strength：1000V
(4) After testing, the appearance is free from damage and meets mechanical properties.
The top of the terminal is immersed in the 2mm depth of the solder pool, the temperature is 230 + 5℃, and the time is 3 + 0.5 seconds.
The welding area should be more than 75%.
When hand welding, the temperature is controlled at 350 + 10 degrees, and the time is 3 + 0.5 seconds. However, abnormal pressure can not be applied to the feet.
There is no abnormal appearance, which is satisfied with mechanical and electrical properties.
Heat resistance test
It was placed at a temperature of 85 + 2℃, and then placed at normal room temperature for 1 hours after 96 hours.
Cold tolerance test
It was placed at a temperature of -40 + 3℃, and then placed in normal room temperature for 1 hours after 96 hours.
1.6 ENVIRONMENT RESISTANCE
It was placed in a temperature of 40 + 2 ℃ and a relative humidity of 90~95%. After 96 hours, it was placed at normal room temperature for 1 hours.
No abnormal appearance，Meet the mechanical and electrical properties。
Test standard state
In the absence of a specified case Test the temperature, humidity, and air pressure as follows：
（1） temperature： 5~35°C 。
（2） humidity： 45~85% 。
（3） pressure： 86Kpa~106Kpa 。
Use of temperature range
It is used at -16 C ~ +60 ℃ temperature.
1.7 SAFEKEEPING METHOD：
（1）If the product is not used immediately, it should be kept at normal temperature without direct sunlight and corrosive gases.
In the environment. But we recommend that we use it as soon as 6 months.
（2）Put the finished products in plastic bags and seal them in the same environment as soon as possible, and use them as soon as possible. Do not overlay excess when saved in order to prevent the pressure from breaking.
（3）Do not overlay excess when saved in order to prevent the pressure from breaking.
2. DRAWING & DIMENSION:
Double-layers paper carton
X pieces per box X inner cartons per shipping carton Each shipping carton X pieces
Gross Weight : xx kg
Net Weight : xx kg
X x Xx X CM